|
Product Application Guide
Commonly used RESINS
Table of Contents of this Page
Primers & Sealers
- Product #12 Epoxy Primer - a
two component, seamless 100% solids epoxy primer system with High Chemical
Resistance and High Bond Strength. The epoxy may be applied as a primer for most
High End Industrial coatings, like Epoxies, MMA, Polyurethane's, Vinyl Esters,
Polyesters, etc.
- PRODUCT #39 Silane
Penetrating Sealer is a one component water based silane that
provides excellent protection to concrete surfaces against attack from
wet/dry, freeze/thaw cycles, and de-icing chemicals. PRODUCT #39
imparts a hydrophobic "water-shedding" effect to concrete, masonry, brick,
stone & wood surfaces. The water repellency helps reduce cracking spalling,
chemical degradation, biological growth, efflorescence, and dirt pick- up.
PRODUCT #39 is easy to use and meets all current VOC regulations.
- Product #40 -
Replaced PRODUCT #41 Silane
Penetrating Sealer
- PRODUCT #41 Silane
Penetrating Sealer is a one (1) component sealer that provides
excellent protection to concrete against attack from wet/dry, freeze/ thaw
cycles, and de-icing chemicals. EPOXYSYSTEMS’ PRODUCT #41 provides a
hydrophobic "water-shedding" effect to masonry surfaces. EPOXYSYSTEMS’
PRODUCT #41 is a penetrating sealer that is repellent to liquid water but
permeable to water vapor: a "breathable" coating.
-
Product #80 Acrylic Sealer
- a clear acrylic
solution formulated to create a clear, non-yellowing protective coating.
EPOXY SYSTEMS’ ACRYLIC SEALER provides a tough, UV and abrasion resistant
film that effectively protects surfaces from moisture penetration, staining,
dirt, dust, and wear. Providing a surface that is easy to clean and
maintain, EPOXY SYSTEMS’ ACRYLIC SEALER is an excellent choice for both
interior and exterior applications.
- EpoxySystems’ Product
#100 uses a unique epoxy technology which allows the contractor to
install epoxy systems on new concrete (4-5 days old) without fear of
moisture entrapment. Product #100 Exhibits greater than 100 times the
permeability of standard epoxy slurries and mortars. Product #100 is used as
a base for EpoxySystems’ Chip and Quartz systems and as a binder for
EpoxySystems’ Resinous Mortar Systems, when moisture is a concern.
-
Product #201 Oil Stop Primer -
a two component, epoxy-amine
undercoating designed to be compatible with petroleum based oil and greases. In
many instances petroleum can penetrate the surface of concrete floors to the
extent that the oil may not be removed by surface cleaning. If untreated, this
oil may migrate back to the surface to cause a delamination.
- Product #203 Cold Temperature Cure Polymeric
Primer - a specially
formulated primer for cold temperature applications. Able to cure at
temperatures as low as 35°F. It is often used in coolers and food preparation
areas that require constant low temperatures. It is frequently used in room
temperature applications to meet super-fast cure, limited shutdown needs.
-
Product #223
Clear Water Based Epoxy Curing Compound,
Sealer and Bonding Agent is a two component
water based epoxy curing that is used to both cure and seal concrete and to bond
freshly placed concrete to existing concrete. It is easily pigmented.
- Product #636
High Temp Chemical Resistant Primer/Topcoat - a 100%
solids amine cured epoxy Novolac that is solvent free. Specifically designed
as a Methanol resistant coating. Product #635 is well suited for use in a
wide array of aggressive acids, alkalies and organic solvents. It produces a
tough, chemical resistant coating on concrete, iron and non-iron surfaces.
As a low viscosity epoxy Novolac it is suitable for hand or spray
application.
- Product #637
High Temp Coating/Primer is a 100% solids
amine cured epoxy Novolac that is solvent free. Suitable for immersion and
non-immersion service particularly in aggressive acid environments. Epoxy
Systems Product #637 produces a tough, chemical resistant coating on
concrete, iron and non-iron surfaces. As a lower viscosity epoxy Novolac it
is suitable as a primer or as a top coating. Excellent against 98% Sulfuric
Acid.
-
Product #671 Conductive Primer/Sealer - EpoxySystems’ Product #671 is a low
viscosity, two component, carbon filled, polyamide modified conductive
primer/sealer formulated with special wetting agents to provide maximum
penetration into concrete surfaces. Product #671 is ideal for both new and old
concrete surfaces. Product #671 provides excellent resistance to wear, and can
be used either alone or as a conductive sealer or as a conductive primer when
used with EpoxySystems’ product #674 Electro-Static Dissipating Urethane Topcoat
and EpoxySystems’ Conductive Systems.
- Product #681 MMA Primer for
MMA Polymer Concrete
- Product #685 MMA Crack Healer and
Sealer is for injection repair or as a penetrating crack repair and
sealer on concrete. It is a two component Methyl Methacrylate resin system
that polymerizes in place. The extremely low viscosity will penetrate into
concrete cracks as fine as 0.003 inches. Has more odor than
684 Crack Welder/Sealer, but is even lower in viscosity,
and lower priced, while maintaining similar end properties.
- Product #801 Fast Set Acrylic Sealer
- 810 Primer for Polyurea
is a two-component, clear, VOC compliant floor coating. PRODUCT #810 is fast
drying and will cure in temperatures as low as 35°F. Its convenient 2A:1B
mixing ratio, no induction time and long pot life simplify mixing and
application. PRODUCT #810 protects by penetrating concrete or wood and has
excellent adhesion to damp concrete, it is an excellent concrete primer.
- Product #824 Concrete Stain and
Coating is a one component, water-repellant concrete stain.
EPOXYSYSTEMS’ PRODUCT #824 penetrates existing concrete and imparts color and
uniformity the surface without affecting the natural texture. Standard colors
are white and gray many other colors of concrete are available.
- Product #825 Epoxy Floor Sealer
is a non-rewettable, polymer emulsion formulated for use with fast or normal
setting floor underlayments.
- Product #826 Floor Curing Agent - Minimum purchase
of 10 each 55 gallon drums required.
- Product #843 - High Solids Epoxy Primer
- Product #844 Concrete Membrane Deck Primer is a 100% solids, two (2)
component polyurethane primer. This thin film primer promotes long term wear
and superior adhesion of the Product #409 Resilient Traffic Bearing Membrane.
The Product #844 penetrates and seals the surface to allow for a smoother,
pinhole free application.
- Product # 845 Penetrant & Prime
Coat - is a 100
% solids, low viscosity, epoxy primer for use on steel, concrete or wood. The
low viscosity and special adhesion promoters make it an excellent penetrant of
rusted steel or concrete. ESI #845 acts as an inert barrier, resistant to
impact, acids, caustics, solvent and thermal shock. The tough water proof
surface is excellent for subsequent coatings.
Penetrates and reinforces rusted steel surfaces. Cures under high humidity. Solvent free; 0.0 lbs. VOC. Good abrasion, heat and impact resistance. No blush or exudation.
- Product #851 Epoxy Siloxane
- Product 870 (65% Solids - Penetrating
Epoxy Sealer) - is a two-component
penetrating epoxy sealer (with very high solids) designed for superior
protection of new concrete or for prolonging the serviceability of
partially-deteriorated concrete. The sealer is a low to medium viscosity
material and is capable of providing an effective membrane barrier to inhibit
moisture migration and corrosive chemical penetration.
In the cured state ESItm Product #850
allows moisture vapor transmission; it seals off moisture entry but still allows
the concrete to breath. When applied to concrete place and finished in
accordance with standards defined in ACI 201 (Guide to Durable Concrete),
Product #850 greatly improves wear resistance of the concrete surface, slows
down the corrosion of reinforcing steel and adds many years' life to the
structure. Product #850 has a solids content of 50% after curing. It may be
applied to dry surfaces at temperatures of 40°F (0°C) or above.
- Product #879 Galvanized and Aluminum Primer
- Product #899 Epoxy
Primer - a damp
primer the is a 100% solids Low-Mod Low Viscosity Primer and Sealer. It may be used as a primer for
any Epoxy Systems’ ™ product, or as a stand alone sealer.
- PRODUCT
#1200 Epoxy Organic Zinc Rich Primer is a two component epoxy primer which provides
both barrier and sacrificial protection against steel corrosion. PRODUCT
#1200 promotes adhesion, dries rapidly, and can be either shop or field
applied.
Back to Table of Contents
Coatings
 |
Product #1 All Purpose Coating - a 100% solids epoxy
Hi-Build epoxy coating used for high foot and light forklift traffic areas
where abrasion resistance is required; for protection against mild corrosion;
and as a decorative waterproof coating for walls, floors, tanks, etc Available
in normal, fast, and Cold Temperature Cure versions. |
|
| Product #1Fast - Shorter Potlife, and faster setting version of
Product #1 |
|
| Product #1Cold Temperature Cure - This is a version of Product #1
that sets even faster than Product#1 Fast. Typically used in colder
temperatures, or where an very fast cure is required. |
|
| Epoxy Systems Product #2
Chemical Resistant Coating - a two component, 100% solids epoxy chemical
resistant coating used to protect chemical concrete, steel and other
structural materials from non-oxidizing acids and alkalines for both interior
and exterior applications. Available in normal, fast, and Cold Temperature
Cure. |
|
| Product #2 Fast - Shorter Potlife, and faster setting version of
Product #2 |
|
| Product #2 Cold Temperature Cure - This is a version of that sets
even faster than Product#2 Fast. Typically used in colder temperatures, or
where an very fast cure is required. |
|
| Product #211 Polyamide Epoxy Coating - Ideal for bonding to steel
and similar surfaces |
|
| Product #212 - Anti-Fouling Coating - Special orders in quantity
only available. |
|
| Product #213 Decoupage Epoxy |
|
| Product #214 Tabletop Resin
- an all-purpose, low viscosity
Epoxy System for coating wooden counter tops, tabletops, bar tops and similar
applications. It forms a glossy, hard surface, which
is resistant to stains. It has excellent clarity and
color retention. It is essentially odorless and can therefore be used in
occupied areas |
|
|
Product #215 Epoxy Polyamine
- a high solids, epoxy-polyamide
combination, chemical curing, quick- drying resin system. Product #215
produces a ceramic like coating on masonry, concrete plaster, cement, asbestos
board, wood, fiberglass, metal and most other rigid materials. Formulated for
applications that require superior adhesion and durability, chemical
|
|
| Product #216 Coal Tar Epoxy
is a two component coal tar epoxy coating, black in color, used to protect
steel, concrete structures, timber, and other construction materials in
corrosive environments. It meets all requirements of Corp. of Engineers C-200,
Federal Specification DOD-P-23236 (SHIPS), and SSPC 16-91. |
|
|
Product #217 Floor Coating Primer |
|
|
Product #218 Floor Coating Intermediate |
|
|
Product#219 Floor Coating Top Coat |
|
| Product #220 Rebar Touch Up Epoxy Coating
is a two component, 70% solids epoxy coating specially manufactured to touch
up damage epoxy coated rebar or to coat rebars not previously protected
against corrosion. |
|
|
Product #222 Water Based Epoxy -
Epoxy Systems’ Product #222 WATER BASED EPOXY COATING is a two component
100% reactive water based multifunctional epoxy resin coating. Product #222
is manufactured to produce the utmost in performance in a safe, water borne
coating. Product #222 provides excellent resistance to salt intrusion, and
excellent adhesion to most common construction substrates. |
|
|
Product #223
Clear Water Based Epoxy Curing Compound,
Sealer and Bonding Agent is a two component
water based epoxy curing that is used to both cure and seal concrete and to
bond freshly placed concrete to existing concrete. It is easily pigmented. |
|
|
Product #226Fast Setting Water Based Epoxy is a
Fast Setting Water Based Epoxy Coating is a two component, 100% reactive,
water based, multi functional epoxy resin coating. PRODUCT #226 is
manufactured to produce the utmost in performance in a safe, water borne
coating. PRODUCT #226 provides excellent resistance to salt intrusion, and
excellent adhesion to most common construction substrates. Product #226 is VOC
Compliant, Fast Curing, and tintable with standard colorants. It is
Internally Flexibilized so it can be applied to metals and plastics. It is
water-reducible and easily applied. |
|
| Product #250 Water Tank Type
Coating is a 100% solids, moisture-
insensitive epoxy coating, containing no solvents. It is mixed at a 2:1 ratio,
produces a tough, chemical and abrasion-resistant coating for dry or damp
concrete, wood or steel surfaces. |
|
| Product #255 Mastic High Build
Epoxy Coating is a 100% solids, moisture-insensitive, epoxy resin
system. When mixed at a 1:1 ratio, by volume, it produces an excellent coating
for dry or damp concrete, wood or steel surfaces. It iss used on piles, piers,
and concrete or steel tanks where concrete or steel needs to be protected from
abrasive environments. |
|
|
Product #256 Impact and Chemical Resistant Epoxy
Coating. |
|
| EpoxySystems'™ Product #315 Polymeric Multi-Colored
Flake Floor Resurfacing System |
|
|
Product #315BC
Polymeric Coating and Base Coat for the 315Chip
Flooring System, It can also be used as a stand alone coating. |
|
|
Product #315BC - Fast Same as
Product #315BC Polymeric Coating for Base Coat for
the 315Chip Flooring System , but with a fast cure.
|
|
|
Product #315BC-Cold Same as Product
#315BC Polymeric Coating for Base Coat for the
315Chip Flooring System , but with a cold temperature
cure. |
|
|
Product #316 Fast Set Flooring
-
a 100 % solids fast setting
two-component epoxy resin system. Is made to set
fast even in temperatures below freezing. It is recommended for flooring,
injection or anchor-bolt grouting in the neat state or as a mortar when mixed
#75 Filler. It exceeds most requirements of
ASTM C-881-99, Types I and IV , Grade 1, Class A. |
|
| Epoxy Systems Product #633 Epoxy Novolac Coating |
|
| EpoxySystems' Vinyl Ester Systems |
|
|
Product #401
Urethane Coating - a two (2) component, high-solids,
urethane coating. Urethane Coating is a two (2) component, high-solids,
urethane coating. It is a superior coating that provides the ultimate in
weather resistance. It offers outstanding abrasion resistance, excellent
chemical resistance and color retention in severe conditions. |
|
| Product #402
Urethane - a two component1 chemical resistant polyurethane
coating. The high gloss finish offers excellent abrasion resistance, chemical
and stain resistance, and color retention. It used equally well on vertical or
horizontal surfaces. It is ideal for concrete floors and walls in warehouses,
storage facilities, aircraft hangers, animal housing, and vehicle maintenance
facilities. |
|
|
Product #403 Urethane Coating Aliphatic |
|
|
Product #404 Fast Cure Urethane Membrane |
|
|
Product #405 Fast Cure Urethane Topcoat. |
|
|
System
#410 Urethane
Traffic Bearing Membrane System is a tough, resilient
system with excellent elongation. It is applied as a 3-step system -
consisting of a primer, traffic bearing membrane - 2 coats, and sealer. It
cures at ambient temperatures and is impermeable to moisture, oils, mild adds,
gasoline, and alkalies. |
|
|
Product #411 Primer for System #410 |
|
|
Product #413 Liquid Flashing for System #410 |
|
|
Product #414 Caulk for under System #410 |
|
|
Product #641LV High Temp Resistant
Mortar is a two component highly cross-linked novolac epoxy resin system.
It is especially formulated to be used as a high temperature grouting or
laminating resin. It is used to protect concrete, steel and other substrates
from high temperatures and corrosion. |
|
|
Product #642
Multifunctional High Chemical Resistance
Epoxy Coating/Bonder |
|
|
Product #644 High Temp
Chemical Resistant Coating. Similar to 641LV, but with
fillers to make it thicker.
|
|
|
Product #645 High Temp Coating |
|
|
Product #690 All Purpose MMA Primer and Mortar |
|
|
Product #1800 Fast Setting Brushable Polyurea Coating
|
|
|
Product #1810 - Elastomeric Polyurea lining |
Back to Table of Contents
Seamless and Industrial Flooring
Most of EpoxySystems'
Coatings can also be used to make seamless
floors. Some of the Seamless Flooring Systems below will also benefit from the
use of a Primer. Contact EpoxySystems'
Technical Support for details.
- Epoxy Systems Product #10
a 100% solids Lo-Mod Low Viscosity adhesive used as a binder for epoxy mortar
systems in patching and grouting applications, as a seal coat for non-skid
surfaces outside, and as a primer to insure high bond strength for coatings
and patches.
- Product #10FAST Lo-Mod Adhesive -Fast Cure
- Product #10COLD Lo-Mod Adhesive Cold Temperature Cure
- EpoxySystems' Product #11 a 100%
solids flexible epoxy joint filler for saw-cut joints of concrete slabs on
grade, or to repair existing slabs. Product #11 absorbs the impact and shock
of heavy loads and steel wheeled traffic, preventing erosion of control joint
edges.
- EpoxySystems' Product #12
a two component, seamless 100% solids epoxy primer system
with High Chemical Resistance and High Bond Strength. The epoxy may be applied
as a primer for most High End Industrial coatings, like Epoxies, MMA,
Polyurethane's, Vinyl Esters, Polyesters, etc.
- EpoxySystems' Product #15 Chemical
Resistant Flooring Resin - a two component, seamless 100% solids epoxy
resurfacing system with High Chemical Resistance. It may be applied as a
coating, or combined with silica sand or EpoxySystems' multi-colored quartz
aggregate to produce a durable, easy to maintain floor, on both new and old
surfaces.
- Product #16 Epoxy Mortar Resin
- a two-component, 100% solids epoxy resin system, mixed at a 1:1 ratio by
volume. Epoxy Systems’ Product #16, mixed with up to 3 parts dry EpoxySystems’
Product #75 Filler produces an economical, high-strength epoxy mortar. Product
#16 exceeds the requirements of ASTM C-881-78, Grade II, Classes A, B & C,
Types I & III. Product #16 is recommended for use in dry environments only.
- Product #17 Decorative Stone
Overlays - a two component, 100% solids high-mod epoxy adhesive used
for bonding stone and other aggregates in all types of flooring applications.
Some uses would include patios, pool decks, walkways and other areas where a
long wearing and decorative system is desired.
- Product #18 General Purpose
Epoxy - a hard set epoxy compound formulated for general use. Product #18
cures at room temperature and is a low viscosity system. This durable,
resilient material requires no post curing to achieve permanent bond strength.
Mixing ratio of 1 to 1 makes this product easy to use. Product #18 solves many
difficult bonding, and epoxy mortar problems. Product has the ability to bond
to a variety of substrates including cannot dry and hard to dry surfaces.
- Product #19 Epoxy Mortar -
a multi-function liquid applied, 100% solids epoxy binder and mortar system
with excellent wear, and chemical resistance. Product #19 is an excellent
general purpose material with excellent clarity and color retention. It is
essentially odorless and so it can be used in occupied areas.
- Product #20
Epoxy Grout - a moisture insensitive,
two-component, 100% solids epoxy resin system manufactured specifically for
use in temperatures of 40°F and below. It is recommended for injection or
anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3
1/4 parts of Product #76 -Epoxy Filler (by volume). PRODUCT #20 exceeds most
requirements of ASTM C-881-90, Types I, Grade 1, Class A.
- Product # 22
Underwater Epoxy Mortar - Pourable
Epoxy Mortar that is a moisture insensitive,
two-component, 100% solids epoxy resin. This material is specifically designed
for use with the Epoxy Systems’ Fiberglass Systems & Shapes.
Can also be used as self-leveling flooring.
- Product #23 - Similar to #22
but in 1:1 mix ratio
- Product #24
Pigmented Mortar - is a multipurpose colored epoxy binder for
EpoxySystems’ Mortar Systems This all purpose epoxy resin is characterized as
an excellent general purpose material with good clarity and color retention.
It is essentially odorless and can therefore be used in occupied areas.
- Product #24
Fast Pigmented Mortar - Fast Cure
- Product #24
Cold Pigmented Mortar - Cold Temperature Cure
- Product #25
Epoxy Mortar Kit standard - a 100% solids epoxy resin and
specially selected aggregate system. Units are preproportioned for ease of
mixing and use on the jobsite. It is a
flowable, self-leveling grout, with handling and physical characteristics
superior to similar grouts.
-
Product #26 Epoxy Mortar Kit -
a 100% solids epoxy resin and
specially selected aggregate system which produces a flowable, self-leveling
grout, with handling and physical characteristics superior to similar grouts.
It is designed for floor resurfacing where high strength and short down
time are needed. Units are preproportioned for ease
of mixing and use on the jobsite.
-
Product #27 Slow Cure Mortar
- Product #28 Epoxy Mortar
- Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for
EpoxySystems’ Mortar Systems This all purpose epoxy resin is characterized as
an excellent general purpose material with good clarity and color retention.
It is essentially odorless and can therefore be used in occupied areas.
-
Product #29 Cold Temperature Cure Mortar
is a specially formulated
binder for cold temperature applications. Able to cure at temperatures as low
as 35°F. They are often used in coolers and food preparation areas that
require constant low temperatures. Product #29 Cold Temperature Cure EPOXY
MORTAR is also frequently used in room temperature applications to meet
super-fast cure, limited shutdown needs.
- Product #203
Cold Temperature Cure Polymeric Primer -
a specially formulated primer for cold
temperature applications. Able to cure at temperatures as low as 35°F. It is
often used in coolers and food preparation areas that require constant low
temperatures. It is frequently used in room temperature applications to meet
super-fast cure, limited shutdown needs
- Product #204
Cold Temperature Cure Polymeric Coating -
is a specially formulated coating for cold
temperature applications. Able to cure at temperatures as low as 35°F. It is
often used in coolers and food preparation areas that require constant low
temperatures. It is also frequently used in room temperature applications to
meet super-fast cure, limited shutdown needs.
- Product #205 Polymeric Flooring Resin
- Product #206 Cold Temperature
Cure Pigmented Polymeric Flooring Resin is a specially
formulated binder for cold temperature applications. Able to cure at
temperatures as low as 35°F. It is often used in coolers and food preparation
areas that require constant low temperatures. Product #206 Cold Temperature
Cure POLYMERIC MORTAR is also frequently used in room temperature applications
to meet super-fast cure, limited shutdown needs. Is available in clear or
colors.
- EpoxySystems'™ Product #315 Polymeric Multi-Colored
Flake Floor Resurfacing System
- Product #315BC Polymeric Coating and Base Coat for the
315Chip
Flooring System, It can also be used as a stand alone coating.
- Product #315BC - Fast Same as
Product #315BC Polymeric Coating for Base Coat for
the 315Chip Flooring System , but with a fast cure.
- Product #315BC-Cold Same as Product
#315BC Polymeric Coating for Base Coat for the
315Chip Flooring System , but with a cold temperature
cure.
-
Product #316 Fast Set Flooring
-
a 100 % solids fast setting
two-component epoxy resin system. Is made to set
fast even in temperatures below freezing. It is recommended for flooring,
injection or anchor-bolt grouting in the neat state or as a mortar when mixed
#75 Filler. It exceeds most requirements of
ASTM C-881-99, Types I and IV , Grade 1, Class A.
- Product #641LV High Temp Resistant
Mortar is a two component highly cross-linked novolac epoxy resin system.
It is especially formulated to be used as a high temperature grouting or
laminating resin. It is used to protect concrete, steel and other substrates
from high temperatures and corrosion.
- Product #1501 Orange Peal Mortar Regular Cure
- Product #1501Fast- Orange Peal Mortar Fast Cure
- Product #1501Cold- Orange Peal Mortar Cold Temperature
Cure
- Product #1502 Cove Resin
- Product #1502Fast- Cove Resin Fast Set
- Product #1502Cold - Cove Resin Cold Temperature Cure
- Product #1503- Epoxy Mortar Resin with Fly Ash
- Product #1503 Fast- Epoxy Mortar Resin with Fly Ash,
Fast Cure
- Product #1503Cold - Epoxy Mortar Resin with Fly Ash,
Cold Temperature Cure
Methyl Methacrylate
- MMA
-
Product #680 MMA Polymer Concrete
is a Polymer Concrete methyl
methacrylate (mma) reactive resin is used as a binder to develop polymer
concrete which produces extremely high strength and chemical resistance with
an abrasion resistant surface. It is prepackaged and preproportioned for easy
mixing and placing at the job site. The liquid polymer and the preproportioned
hardener filler is mixed either in the polyethylene bag or in a mortar mixer.
- Product #681 MMA Primer for
MMA Polymer Concrete
- Product #682
MMA
Polymer Concrete High Molecular Weight is a second generation
polymer concrete. PRODUCT #682 is non-hazardous, odorless and a non red label
product. The monomer has a flash point greater than 200°F. PRODUCT #682
exhibits excellent physical properties and no shrinkage on curing. PRODUCT
#682 provides superior chemical resistance to all portland cement concretes.
- Product #683 MMA High Molecular
Weight Primer for MMA Polymer Concrete High Molecular
Weight
- Product #684 Crack
Welder/Sealer is a High-Molecular Weight Methacrylate, specifically
formulated to seal new or hardened cracked concrete and masonry surfaces.
PRODUCT #684 is a three component, low viscosity, monomeric penetrating
sealer, ideally suited to prevent water, chloride or other deleterious liquids
from penetrating concrete. PRODUCT #684 is used to seal new or existing
concrete. PRODUCT #684 is used to arrest concrete deterioration due to alkali
silica reaction of Portland cement concrete.
- Product #690 All Purpose MMA Primer and Mortar
Back to Table of Contents
Conductive and Electrostatic Dissipative Coatings and Flooring
-
Product #671 Conductive
Primer/Sealer - EpoxySystems’ Product #671 is a low
viscosity, two component, carbon filled, polyamide modified conductive
primer/sealer formulated with special wetting agents to provide maximum
penetration into concrete surfaces. Product #671 is ideal for both new and old
concrete surfaces. Product #671 provides excellent resistance to wear, and can
be used either alone or as a conductive sealer or as a conductive primer when
used with EpoxySystems’ product #674 Electro-Static Dissipating Urethane
Topcoat and EpoxySystems’ Conductive Systems.
- Product #672 Conductive Epoxy
- Product #673 Conductive Terrazzo
- Product #674 Electrostatic Dissipating Urethane Topcoat
- Product #675 Electrostatic
Dissipating Water Borne Epoxy Topcoat-a pigmented, water emulsion epoxy
electro-static dissipative finish designed to have maximum penetration into
concrete surfaces to provide high bond strength and adhesion. It has very low
odor and can be used in occupied areas as a finish sealer in Thin-Film
Electro-Static Dissipative Coating Systems.
Crack Repair (Wet and Damp above 32/F, Dry 0/F and above)
- Surface sealing for injection - Cannot dry, damp, and dry
surfaces
- Pressure injection by Epoxy
- Epoxy Systems Product #3 (100% Solids, Epoxy Injection Resin)
- Product #301
2:1 Injection Resin, low
Modulus - a 100% solids low viscosity epoxy adhesive used to
restore cracked structural concrete by the pressure injection method and to
grout cracks in a horizontal plane by gravity.
- Product #302
Injection a 100% solids low viscosity moisture
insensitive epoxy adhesive used to restore cracked structural concrete by
the pressure injection method and to grout cracks in a horizontal plane by
gravity.
- Product #303
Low Viscosity a is a two
component, 100% solids, moisture insensitive epoxy resin system, mixed at a
2:1 ratio, with a viscosity of light-weight oil. Product #303 exceeds the
requirements of ASTM C 881 87, Types I, II, Grade 1, Class "B" and "C". Use
neat for grouting damp and dry cracks or as a penetrating sealer on
concrete, and wood. May also be mixed with Special Fillers (Products
#72-75), to create epoxy mortars.
-
Product #304 Injection Resin and Mortar Binder
is a moisture insensitive, two-component,
100% solids epoxy resin system designed specifically for use in temperatures
of 40°F and below. It is recommended for injection or anchor-bolt grouting
in the neat state or as a mortar when mixed with up to 3 1/4 parts of
PRODUCT #75 Filler (by volume). PRODUCT #304 exceeds requirements of ASTM
C-881-90, Types I, Grade 1, Class A.
- Pressure Injection by Urethane
- Product #4 Urethane Injection
- a one-component, "Acetone Free", MDI based hydrophilic sealing and
grouting compound used to stop water leaks in wet environments. Product #4,
as it mixes with existing water, cures rapidly into a tough, flexible,
closed-cell compound which is insoluble to water and most other chemicals.
- Product #420
Urethane Injection is a one component, ACETONE FREE, MDI
cross-linked, hydrophilic sealing and grouting polymer. The liquid resin
reacts rapidly in the presence of water or moisture. EpoxySystems’ Product
#420 reacts with water and expands to form an impermeable HYDROPHOBIC
barrier. When reacted and hardened, EpoxySystems’ Product #420 is insoluble
to water and other aggressive chemicals.
- Product #421 Urethane Injection
resin
- Product #422 Replace by Product
#420 Urethane Injection resin flexible
- Product #423 Urethane Injection resin
- Product #424 Structural Foam Urethane
- Product #425 Floatation MDA
- Product #426 Urethane Gel
- Product #427 Urethane Cleaner
- Product #428 Urethane Safety Cleaner
- Product #429 Urethane Accelerator
- Gravity Feed with Methyl Methacrylate (MMA)
- Product #684 Crack
Welder/Sealer is a High-Molecular Weight Methacrylate, specifically
formulated to seal new or hardened cracked concrete and masonry surfaces.
PRODUCT #684 is a three component, low viscosity, monomeric penetrating
sealer, ideally suited to prevent water, chloride or other deleterious liquids
from penetrating concrete. PRODUCT #684 is used to seal new or existing
concrete. PRODUCT #684 is used to arrest concrete deterioration due to alkali
silica reaction of Portland cement concrete.
- Injection Equipment and tools
- Manual Injection Pump
- Injection Ports
- Binary Tubes 75 ML
- Binary Tubes 150 ML
- Binary Tubes 300 ML
- Static Mixing Tubes for Binary Tubes
- Manual Gun for Binary Tubes
- Pneumatic Gun
- Vacuum Swivel Drill
- Vacuum Swivel Drill Bits
Patching, and
Resurfacing
- Low Viscosities (Horizontal)
- Product #653 Emergency Epoxy Liquid Grade
- Also can use products listed under Overlays
- High Viscosities / Gels (Horizontal, Vertical and Overhead)
Back to Table of Contents
Overlays
- Product #21
Pumpable Mortar can be used underwater -
a Pumpable Epoxy Mortar that is a
moisture insensitive, two-component, 100% solids epoxy resin. This
material is specifically designed for use in marine environments, but can
be used in wet or dry strippable form applications. #21 can be pumped or
poured into the void created between the existing structure and the Epoxy
Systems’ Corrosion Free Jacket. Dewatering is not required.
- Product # 22
Underwater Epoxy Mortar -
Pourable Epoxy Mortar that is a moisture
insensitive, two-component, 100% solids epoxy resin. This material is
specifically designed for use with the Epoxy Systems’ Fiberglass Systems &
Shapes. Can also be used as self-leveling
flooring.
- Product #23 - Similar to
#22 but in 1:1 mix ratio
- Product #
707 Splash Zone & Under Water Epoxy Paste is a
moisture-insensitive, two-component, 100% solids epoxy-resin system. When
mixed at a 1:1 ratio, by volume, this product produces a paste-like
material that is ideal for protection or restoration of concrete, steel
and timber piles and other structural elements in marine environments.
-
PRODUCT #8100 Underwater Mortar
is a non-water separable grout or concrete that requires
merely the addition of potable water at the job site and is mixed to the
desired consistency. It may then be pumped or poured in water without any
wash-out (separation) of the cement paste from other constituents.
Bonding
Adhesives
Almost all of our resins can be used for bonding, and/or as adhesives.
The products listed below are primarily used for bonding
and/or as adhesives, but many are useful for patching or surface sealing of
cracks as well.
- Product #5 Fast Set Gel Adhesive
- a 100% solids high-mod epoxy gel adhesive used for vertical and overhead
bonding applications and structural repairs. It is also used as a grout for
anchor bolts, dowels and rebar.
- Product#6 Gel - Normal Setting
Adhesive - high-mod epoxy gel adhesive used for vertical and overhead
bonding applications and structural repairs. It is also used as a grout for
anchor bolts, dowels and rebar.
- Product #6SC Long Pot life
Adhesive produces a non-sagging material that is ideal for repairs on
vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the requirements
of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C"
-
Product #7 All Purpose
Epoxy Bonding Agent is a two component, 100% solids epoxy resin system
designed to bond new concrete to old and other materials to concrete.
It has a convenient 1:1 mix ratio, by volume with a viscosity similar to
heavyweight oil. It exceeds the requirements of ASTM C-881-90, Types I, II, IV
and V, Grade 2, Class "B" and "C".
- Product #7SC - a 100%
solids high-mod epoxy adhesive used to bond fresh concrete to cured concrete,
steel to fresh or hardened concrete, as a grout for anchor bolts, dowels and
rebar, as a binder for epoxy concrete, and for bonding other dissimilar
materials. It is similar to Epoxy Systems’ ™ Product #7 but with a slower cure
to allow more time for concrete pours.
- )
- Product #541 Polyester Anchor Bolt Adhesive
- Product #701
Flexible Bonder -
a two component, 100% solids, mixed at a 1:1 ratio adhesive formulated to give
a permanent bond to ceramic, metal, concrete and elastomeric surfaces.
It is thixotropic, non-sag, and is easily applied by
trowel.
-
Product #702 Traffic Marker Adhesive
is a two component, 1:1 ratio, 100% solids, moisture insensitive epoxy resin
system manufactured to bond delineators and traffic markers to median
barriers, parapets, and roadways. It is a normal setting adhesive for use in
temperatures above 50° F. PRODUCT #702 will bond to steel, concrete, and
asphalt. It exceeds the requirements of AASHTO M237 Type IV.
- Product #703
Flexible Gel Adhesive is a 100%
solids, moisture insensitive epoxy resin system, containing no solvents. When
mixed at a 2:1 ratio by volume, it produces a non-sagging material that is
ideal for repairs on vertical or overhead surfaces. It exceeds the
requirements of ASTM C 881-87, Types I, II, and III Grade 3, Class "B", "C",
"E" and "F".
-
Product #704 Emergency Epoxy -
is a rapid setting, two component, 1:1 ratio epoxy adhesive. It sets in six
minutes and can be put into service in one hour regardless of temperature. It
was designed to bond metals, glass, concrete and wood in a matter of minutes.
-
Product #705 Flexible Adhesive
- a Two
Component Flexible Adhesive is a two component flexible adhesive, formulated
to bond plastics to various substrates. Will adhere plastics to other
plastics, concrete, steel, wood and masonry. It is thixotropic and is easily
applied by serrated trowel.
- Product #706
Heat Resistant Bonder/Mortar
is a 100% solids, moisture
insensitive epoxy adhesive and repair material. When A and B Components are
mixed they produce a gel consistency similar to petroleum jelly, which will
not sag or run on a vertical or overhead surface application.
- Product # 707
Splash Zone & Under Water Epoxy Paste is a
moisture-insensitive, two-component, 100% solids epoxy-resin system. When
mixed at a 1:1 ratio, by volume, this product produces a paste-like material
that is ideal for protection or restoration of concrete, steel and timber
piles and other structural elements in marine environments.
- Product #708 Low Viscosity Epoxy
Adhesive for Wood Laminating
- Product #709
Wood Laminating Adhesive - Laminating adhesive for cold press, hot
press, or radio frequency press in the production of veneered tops and end
panels, solid and hollow cored doors and face and edge glue lumber.
- Product #710
Tile Adhesive - is a
Synergistic Polymer formulated and manufactured to produce the utmost in bond,
waterproofing and impact resistant properties. It
may be used with any kind of tile, be it ceramic, fiber reinforced, steel,
glass, wood or concrete. Due to its elasticity,
it will permit movement of substrate to which the tiles are bonded, due
to changes in temperature or creep (shrinkage) in concrete substrate during
aging.
- Product #711
Novolac Adhesive
- Product
#712 a two component flexible sealant, formulated to repair leaking
electrical equipment and circuit breakers. It bonds tenaciously to ceramics,
plastics, metals and most substrates.
-
Product #713 Dowel Bar and Anchor Bolt Adhesive
is a two component, thixotropic, fast setting epoxy
adhesive. It is specifically formulated with an easy to use, non sag
consistency. The special high function resin system allows cure in
temperatures as low as 20 F. The non-sagging properties will permit the
material to be pumped or gunned into horizontal holes for anchoring rebar or
steel bolts. PRODUCT #713 exceeds the requirements of ASTM C 881-90 Types, I,
II, Grade 3, Class A
-
Product #714 Precast Segmental
Adhesive is a 100% solids, gelled epoxy adhesive
formulated to the requirements of ASTM C-881-90, Type VI, Grade 3, Class D, E,
or F. AASHTO M-235-90 duplicates the technical requirements of ASTM -C-881-90.
Expansion Joint Materials
& Sealants
- Epoxy - #11
- Foam - Cross-linked closed celled expanded ethylene vinyl acetate
- #63 Bonded in place with #5 or #18
- Sealants
Back to Table of Contents
Chemical Resistance and Chemical Containment
- Epoxy - Chemical Resistant
 | Epoxy Systems Product #2
Chemical Resistant Coating - a two component, 100% solids epoxy chemical
resistant coating used to protect chemical concrete, steel and other
structural materials from non-oxidizing acids and alkalines for both interior
and exterior applications. Available in normal, fast, and Cold Temperature
Cure. |
|
| Product #2 Fast - Shorter Potlife, and faster setting version of
Product #2 |
|
| Product #2 Cold Temperature Cure - This is a version of that sets
even faster than Product#2 Fast. Typically used in colder temperatures, or
where an very fast cure is required. |
|
|
| EpoxySystems' Product #15 Chemical
Resistant Flooring Resin - a two component, seamless 100% solids epoxy
resurfacing system with High Chemical Resistance. It may be applied as a
coating, or combined with silica sand or EpoxySystems' multi-colored quartz
aggregate to produce a durable, easy to maintain floor, on both new and old
surfaces. |
- Novolac Epoxy
- Highly Chemicals
- Vinyl Ester
- System
#83 Vinyl Ester
- use in a wide range of industrial
applications. ESI™ VINYL ESTER SYSTEMS can be installed as a coating, slurry,
or mortar to meet various chemical and heat resistance needs.
- Product #84 Universal Primer- Used for EpoxySystems System #83 and many
other EpoxySystems' Products
- Product #85 Vinyl Ester Mortar Product
- #86 Vinyl Ester Topcoat Product
- Product #670
Vinyl Ester General Purpose
- #87 General Purpose Vinyl Ester
- Product #669 Strait Vinyl Ester Resin
- Joints
High Temperature
In addition to the Products below, Most
Novolac Epoxies are capable of withstanding up to 300 degrees F.
- Product #634
Novolac High Temperature Epoxy
- Product #636 High
Temp Chemical Resistant Primer/Topcoat - a 100% solids
amine cured epoxy Novolac that is solvent free. Specifically designed as a
Methanol resistant coating. Product #635 is well suited for use in a wide
array of aggressive acids, alkalies and organic solvents. It produces a tough,
chemical resistant coating on concrete, iron and non-iron surfaces. As a low
viscosity epoxy Novolac it is suitable for hand or spray application.
- Product #637
High Temp Coating/Primer
- Product #640
Chemical & Heat Resistance
-
Product #641
High Temp Epoxy is a
moisture-insensitive, two-component, 100% solids epoxy coating. It is
especially formulated to protect concrete, steel and wood subject to high
temperatures and corrosion.
- Product #641LV High Temp Resistant
Mortar is a two component highly cross-linked novolac epoxy resin system.
It is especially formulated to be used as a high temperature grouting or
laminating resin. It is used to protect concrete, steel and other substrates
from high temperatures and corrosion.
- Product #642
Multifunctional High Chemical Resistance
Epoxy Coating/Bonder
- Product #644 High Temp
Chemical Resistant Coating. Similar to 641LV, but with
fillers to make it thicker.
- Product #645 High Temp Coating
- Product #706
Heat Resistant Bonder/Mortar
is a 100% solids, moisture
insensitive epoxy adhesive and repair material. When A and B Components are
mixed they produce a gel consistency similar to petroleum jelly, which will
not sag or run on a vertical or overhead surface application.
Wood Repairs
- Injection - see
Crack Repair
- Patching -
- Product #5 Fast Set Gel Adhesive
- a 100% solids high-mod epoxy gel adhesive used for vertical and overhead
bonding applications and structural repairs. It is also used as a grout for
anchor bolts, dowels and rebar.
- Product#6 Gel - Normal Setting
Adhesive - high-mod epoxy gel adhesive used for vertical and overhead
bonding applications and structural repairs. It is also used as a grout for
anchor bolts, dowels and rebar.
- Product #6SC Long Pot life
Adhesive produces a non-sagging material that is ideal for repairs on
vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the requirements
of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C"
- Product #703
Flexible Gel Adhesive is a 100%
solids, moisture insensitive epoxy resin system, containing no solvents.
When mixed at a 2:1 ratio by volume, it produces a non-sagging material that
is ideal for repairs on vertical or overhead surfaces. It exceeds the
requirements of ASTM C 881-87, Types I, II, and III Grade 3, Class "B", "C",
"E" and "F".
- Modeling and wood working repairs - Polyester Wood Filler
Fillers
- Product #50 Polypropylene Anti-skid Fine Product
- #51 Polypropylene Anti-Skid Course Product
- #52 Polycarbonate Anti-skid Fine Product
- #53 Polycarbonate Anti-skid Course
- Product #64 Conductive Aggregate
- Product #65 Tile Grout Aggregate Product
- #66 Round Quartz Colored Fine - a pure silica sand as the basic mineral.
Silica is an extremely hard abrasion resistant and chemically inert mineral,
ideal for use in conditions that - at times - may be severe. Flooring surfaces
produced with high density silica combined with Industrial Flooring Resins
produced by us consistently show greater resistance to wear
than surfaces filled with minerals or many other resins or binders..
- Product #67 Rounded Quartz
Colored Medium Aggregates - Similar to Product #66,
but larger.
- Product #68 Angular Quartz - Similar to Product #66 but angular.
- Product #69 50% Benzyl Peroxide (BPO) Powder
- Product #71 Fumed Silica Thixotropic Agent Product
- #72 Grade 000 Silica Aggregate Product
- #73 Grade 00 Silica Aggregate Product #74 Grade 0 Silica Aggregate
-
Product #75 Silica Filler
is a very clean, specially graded
natural silica aggregate. Product #75 is oven dried just prior to packaging,
this makes it suitable for use in epoxy grouts. When mixed with EpoxySystems
products, Product #75 makes excellent high strength products.
- Product #76 Epoxy Extender Product
- #77 Broadcast Sand Product
- #78 Self leveling filler Product
- #79 Ground Walnut shell anti-skid aggregate
- Product #81
Epoxy Gel Extender is a
specially formulated blend of fine granules and plasticizers for use with
trowelable (thixotropic) epoxy materials.
-
Product #82 Mortar Blend Aggregate
- Product #340 Colored Chips forChip
Flooring
Elastomeric Waterproofing
Membranes & Roofing Materials
Almost all of our products create a waterproofing membrane.
The products here have the additional advantage of being elastomeric. That gives
them more tolerance for movement.
- Product #600
Flexible Novolac
- Flex Epoxy- Epoxy
Membrane - a flexible resin used as an epoxy membrane and as a
flexible epoxy mortar. It is a two component, 100% solids epoxy used as a base
in many Flexible Epoxy Floor and Mortar Systems. It resists cracking caused
by horizontal substrate movement, providing a crack resistant, resilient,
sound absorbent, waterproof, durable floor. It offers stress-relieving
properties for floor slabs that show movement or vibration. It is excellent
for use in areas such as mechanical equipment rooms, large animal rooms and
activity centers.
Polyesters
- Product #500 Polyester Wood
Filler Pine
- Product #501 Polyester Wood
Filler Mahogany
- Product #502 Polyester Wood Filler Hardener 1
oz.
- Product #503 Polyester Wood Filler Hardener 4
oz.
- Product #504 Polyester Paste Gray
- Product #505 Polyester Paste Black
- Product #540 Anchor Set a three
component, flowable, fast-setting, 100% reactive polyester grout specifically
formulated for anchor bolt setting. It may also be used as a grout for floor
topping where chemical resistance is required.
Cement Based Products & Concrete Additives
- Product #105 Concrete
Catalyst
- Product #550 Rapid Setting Trowel mortar
- Product #551 Thin Patch
- Product #1000
fast setting Mortar
- Product #1001 fast setting Fiber Reinforced Mortar
- Product #1002 Polymer Modified Mortar
- Product #1003 Feather Patch - one component Polymer
Modified cementitious repair mortar that can be used for interior and exterior
repairs
-
Product #1004 Self Leveling Floor
Topping - is a one component copolymer modified cementitious topping.
It is ready to use with only the addition of clean
water to activate the polymer modified cement topping. It
has a special blend of plasticizers to provide zero shrinkage, high
flow and bonding properties necessary for
floor topping.
- Product #1005 - Rapid Setting Mortar
- Product # 1006 Self leveling Underlayments
- Product #1007 Polymer Repair Mortar
- Product #1400 fast setting Fiber Reinforced Mortar
- Product #1450 Silica Fume Concrete Additive
- Product #1451 Catalytic Agent for Concrete
- Product #1452 Synthetic Fiber Additive for Concrete
PRODUCT #8100 Underwater Mortar
is a non-water separable grout or concrete that requires merely
the addition of potable water at the job site and is mixed to the desired
consistency. It may then be pumped or poured in water without any wash-out
(separation) of the cement paste from other constituents.
Tools
Miscellaneous Products
-
Product #224 Water Cleanable Epoxy Mortar Resin
is a user friendly, water cleanable, 100%
solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers,
and stone, it is supplied in pre-packaged kits containing resin, hardener, and
(in the Product #225 Kit) mineral fillers that produce a dense, uniform seal.
Typical applications for #224 require resistance to thermal shock, chemicals,
and heavy traffic including meat packers, breweries, canneries, bottlers, CIP
areas, and pharmaceutical formulators.
- Product #225 Water Cleanable Epoxy Mortar Kit -
includes Product #224 along with the aggregate. Mix the
three components together for a ready to use system.
- Product
#712 a two component flexible sealant, formulated to repair leaking
electrical equipment and circuit breakers. It bonds tenaciously to ceramics,
plastics, metals and most substrates.
- Product #1600 Black Pigment Dispersion in Epoxy
- Product #1625 Red Pigment Dispersion in Polyester
- Product #1626 White Pigment Dispersion in Polyester
- Product #1627 Blue Pigment Dispersion in Polyester
- Product #1628 Green Pigment Dispersion in Polyester
- Product #1629 Various Colored Pigment Dispersions in Polyester
-
Product #1700 epoxy compound
used as an electrical encapsulation material where ease of use and high
electrical resistivity are needed. It is a low viscosity, low odor material
with a pourable viscosity. It has a convenient 1 to 1 by volume mix ratio and
a long pot life. It has a very low exotherm on curing allowing for large parts
with extremely low shrinkage
Back to Table of Contents
 For information on Epoxy
Systems, Inc.
|
