 |
|||
|
|
|||
|
|
|
EpoxySystems' Product #8100 Epoxy Systems’ Under Water Mortar DESCRIPTION PRODUCT #8100 Underwater Mortar is a non-water separable grout or concrete that requires merely the addition of potable water at the job site and is mixed to the desired consistency. It may then be pumped or poured in water without any wash-out (separation) of the cement paste from other constituents.ADVANTAGES PRODUCT #8100 Underwater Mortar offers great economy when compared to two-component grouting materials. PRODUCT #8100 Underwater Mortar is ready-to-use; just mix with potable water to the desired consistency. PRODUCT #8100 does not require the careful and cumbersome placement of tremie pipes and the continual concern with the maintenance (during placement operations) of the tremie seal required with the use of conventional portland cement mortars or grouts. PRODUCT #8100 can be pumped or poured in confined or unconfined areas.PHYSICAL PROPERTIES Co lor Concrete GrayAge at Test Compressive Strength (ASTM C-109) 24 hours 1,500 psi (10.34 MPa) 3 days 2,000 psi (13.79 MPa) 7 days 3,000 psi (20.68 MPa) 28 days 5,000 psi (34.47 MPa) Length Change ASTM C-157 0 HOW TO USE All deteriorated concrete should be removed by waterblasting or chipping to sound concrete. PRODUCT #8100 Underwater Mortar can be mixed with up to 1.5 gallons (5.3 L) of water per 50 lb. (23 kg.) bag, and will produce an extremely flowable, yet non-shrinking grout. Be sure temperature after mixing is no less than 50 F. COVERAGE Each 50 lb. (23 kg.) bag will yield approximately .40 cu. ft. (11,326 cm3) of grouting mortar at a pourable consistency. LIMITATIONS PRODUCT #8100 Underwater Mortar should not be used at temperatures below 40 F.CAUTION: Contains Portland Cement and Silica Sand. Cement powder or freshly mixed concrete, grout or mortar may cause skin injury. Avoid contact with skin; wash exposed areas promptly with water. If any cement powder or mixture gets into eyes, rinse immediately and repeatedly with water. Get prompt medical attention! Dust harmful if inhaled. Use with adequate ventilation. Avoid breathing dust.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
