|
|
|
EpoxySystems' Product #39 Water Based Silane Penetrating Sealer DESCRIPTION: PRODUCT #39 Silane Penetrating Sealer is a one component water based silane that provides excellent protection to concrete surfaces against attack from wet/dry, freeze/thaw cycles, and de-icing chemicals. PRODUCT #39 imparts a hydrophobic "water-shedding" effect to concrete, masonry, brick, stone & wood surfaces. The water repellency helps reduce cracking spalling, chemical degradation, biological growth, efflorescence, and dirt pick- up. PRODUCT #39 is easy to use and meets all current VOC regulations. ADVANTAGES:
WHERE TO USE: PRODUCT #39 can be used for sealing bridge decks, parking garages, parapet walls, roadways, structural concrete, brick work (clay and lime sand), wood and mortar. PHYSICAL PROPERTIES: Color Clear water solution PRODUCT #39 at 125 square feet per gallon, tested in accordance with NCHRP Report # 244, produces the following results: Reduction of water absorption into Concrete 87% Reduction of chloride content into Concrete 87 % UV 90 day exposure (ASTM C 1378) No change in appearance Flash Point None COVERAGE: Normal application - apply two (2) coats at approximately 250 square feet per gallon per coat. To meet or exceed NCHRP report 244 - apply two (2) coats at 125 square feet per gallon average. The second coat may be applied immediately after first is fully absorbed. A coverage of 200 square feet per gallon may be acceptable for general purpose use. For best results, 2 coats are recommended. SURFACE PREPARATION: Surfaces must be clean and sound. While some moisture present in the concrete or masonry will not affect the performance of PRODUCT #39, the drier the surface, the deeper the penetration. APPLICATION: Stir well before use. PRODUCT #39 may be applied by spray (using hand-pumped pressure sprayer), brush, roller - or dipping of masonry units. For best results, use hand-pressure spray equipment instead of compressed air. For best results on most masonry surfaces, two (2) applications are recommended. Dense new concrete surfaces may only require one (1) application. PACKAGING: Five (5) gallon cans and fifty-five (55) gallon drums. SHELF LIFE: 12 months LIMITATIONS: Do not apply on or through standing water. Material is not intended to seal moving cracks from moisture intrusion. PRODUCT #39 is not to be used to prevent leaks from hydrostatic pressure. Do not apply at surface temperatures below 40oF, or when surface temperature is expected to fall below 40oF within four (4) hours after application. CAUTION: Alkaline Material: In case of contact, immediately flush eyes or skin with plenty of water for at least fifteen (15) minutes. Call a physician in case of severe skin or eye irritation. Wash clothing before re-use. Wear protective clothing, goggles, gloves, and/or barrier creams. FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
