 |
|||
|
|
|||
|
|
|
EpoxySystems' Product #409 Resilient Traffic Bearing Membrane
PRODUCT #409 Resilient Traffic Bearing Membrane is a 100% solids, ambient cure impermeable elastomer. PRODUCT #409 is resistant to moisture, oils, mild acids, gasoline, and alkalies. PRODUCT #409 when applied to concrete or other surfaces, is resilient and accommodates movement in concrete substrates. PRODUCT #409 is used as a traffic bearing membrane or non-skid coating that retains color and physical properties when exposed to harsh UV conditions.ADVANTAGES
PHYSICAL PROPERTIES
SURFACE PREPARATION On Steel - Prepare in accordance with Steel Structures Painting Council Surface. Preparation SSPC-SP6 metal blast cleaning. All work blasted should be coated the same day. Apply PRODUCT #1200 Zinc Rich Primer to prime steel. Use in accordance with the PRODUCT #1200 Zinc Rich Primer data sheet. Allow to cure a minimum of 2 hours and a maximum of 48 hours before applying membrane.On Concrete: Concrete surfaces should be water or abrasive blasted to remove dirt, curing compounds, existing coatings or laitance to provide a clean sound bonding surface. If water blasted, surface should dry for 24 hours before placing coating. Prime surface with PRODUCT #844 primer. This is a water based treatment mix with tap water and apply immediately. MIXING Stir B Component before combining with A Component. Mix material to the proper ratio, 4 A to 1B with a mixing paddle and slow speed drill for a minimum of 2 minutes until thoroughly mixed. Avoid entrapping air while mixing. APPLICATION Pedestrian Grade - Recommended DFT of system 27.0 to 34.0 mils DFT. Primer - One Coat Product #844 at 3.0 to 4.0 mils WFT to achieve 3.0 to 4.0 mils DFT. Intermediate - One Coat Product #409 at 12.0 to 15.0 mils WFT to achieve 12.0 to 15.0 mils DFT. Finish - One Coat Product #409 at 12.0 to 15.0 mils WFT to achieve 12.0 to 15.0 mils DFT. The use of rounded silica sand is recommended to produce an anti-slip or non-skid finish. Traffic Grade - Recommended DFT of system 53.0 to 64.0 mils DFT. Primer - One Coat Product#844 at 3.0 to 4.0 mils WFT to achieve 3.0 to 4.0 mils DFT. (lightly seed while wet with a rounded 16 / 30 silica) Intermediate - One coat Product #409 at 25.0 to 30.0 mils WFT to achieve 25.0 to 30.0 mils DFT. (broadcast while wet with a rounded 20 / 40 silica at a rate of 1/4 to 1/2 pound per square foot) Finish - One coat Product #409 at 25.0 to 30.0 mils WFT to achieve 25.0 to 30.0 mils DFT. Apply first coat of PRODUCT #409 by roller or brush at a rate of 80 sq. ft. per gallon. Film thickness approximately 20 mils wet and dry. Wait a minimum of 8 hours or a maximum of 5 days before applying second coat of PRODUCT #409. Apply second coat of PRODUCT #409 at a rate of 80 sq. ft. per gallon. For a non skid surface broadcast Product # 75 into the second coat at a rate of ½ pound per sq. ft. CLEAN UP: Wash equipment and tools with MEK, lacquer thinner, or acetone (immediately after use or before coating cures.) LIMITATIONS: Thinning may result in loss of adhesion of cured material and promote rapid deterioration protective properties. Do not apply PRODUCT #409 on wet surfaces or below 50°F. Lower temperatures will prolong curing considerably. PACKAGING: 5 gallon Unit STORAGE: PRODUCT #409 should be stored in a dry area between 65°F and 90°F. CAUTION: Contains organic isocyanates. Avoid contact with skin and eyes. Do not ingest. Keep away from foodstuffs and wash thoroughly before smoking or eating. Should skin contact occur, wash skin well with soap and water. Should eye contact occur, flush thoroughly for at least 15 minutes with water. Get medical attention.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
