 |
|||
|
|
|||
|
|
|
Epoxy.com Product #713 Epoxy Dowel Bar and Anchor Bolt Adhesive Note: This product is not a stock item and requires a larger minimum order. For most applications Epoxy.com Product #702 will get the job done as well or better than this product. Product #713 has a very short pot life (6 minutes). Product #702 has a longer pot life (10 minutes). This effectively doubles the working time after it is mixed. This longer pot life results in a product that is easier to use and because of that can yield better results. DESCRIPTION Product #713 Dowel Bar and Anchor Bolt Adhesive is a two component, thixotropic, fast setting epoxy adhesive. It is specifically formulated with an easy to use, non sag consistency. The special high function resin system allows cure in temperatures as low as 20 F. The non-sagging properties will permit the material to be pumped or gunned into horizontal holes for anchoring rebar or steel bolts. Epoxy.com PRODUCT #713 exceeds the requirements of ASTM C 881-90 Types, I, II, Grade 3, Class APRIMARY USE
ADVANTAGES
APPLICATION PROPERTIES
PHYSICAL PROPERTIES RESULTS
SURFACE PREPARATION For best results, areas where the material is applied must be free of laitance, grease, oil, and any other contaminants which would inhibit a bond. Abrasive blasting, water blasting, or wire brushing for surface preparation are recommended. MIXING Mixing occurs when the material is discharged through a static mixer using a double barrel gun. COVERAGE One unit consists of (2) 10 fluid oz. (30 centiliters) tubes & yields 36 cu.in. = 1 liter PACKAGING (2) 10 oz. (30 centiliters) Double Barrel Tubes with Static Mixer 2 gallon units (8 liters), 10 gallon units (38 liters) , 110 gallon units (416 liters) LIMITATIONS Epoxy.com PRODUCT #713 should not be used when surface temperatures are below 20o F. CAUTION "A" Component contains epoxy resin . DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.FIRST AID In case of skin contact, immediately wash with soap and water. in case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
