|
|
|
EpoxySystems' Product #711 Multifunctional Novolac Adhesive
DESCRIPTION: Product #711 Multifunctional Epoxy Coating/Adhesive is a two component, 100% solids, one coat trowel grade or grout pump applied protective coating designed to provide cavitation, erosion and corrosion resistance to metallic and non-metallic surfaces. Product #711 acts as a barrier against extremely harsh environmental factors such as low and high PH, temperatures extremes, dry and fluid particulate flow and corrosive chemical attack.USES: PGD scrubber duct Tanks and vessels De-min concrete pads Water boxes Ball mill sumps Heat Exchangers PHYSICAL PROPERTIES: Finish Semi-gloss Color Red (Black by Special Order) Specific Gravity 1.6 Mixing Ratio 2 part "A" to 1 part "B" Pot Life 30 Minutes + @ 77oF Dry Time 2 hours @ 77oF Recommended Film Thickness 45 mils/min.; 60 mils/nominal 80 mils/maximum Coverage Rate One gallon covers approximately 26.7 ft.2 at 60 mils Flash Point Above 200oF CURED PROPERTIES: Compressive Strength (ASTM D-695/7 days) 15,000 p.s.i. Flexural Strength (ASTM D-790/7 days) 13,500 p.s.i. Tensile Strength (ASTM C-190/7 days) 8,000 p.s.i. Shear Strength (ASTM D-1002 Tensile: Steel to Steel) 2,450 p.s.i. Operating Temperature Wet: 300oF Dry: 400oF PH Range 0.5 to 13.5 MIXING: Mix ratio is two parts by volume base ("A") to one part by volume hardener ("B"). CLEANING: Clean all equipment immediately after use with MEK or acetone.
CURE CYCLE: The following standards may be used in assessing what activities can be carried out after an application of Product #711. Temperature 75oF Overcoating 1 to 2 hours Movement/Light Stress 8 hours Traffic Bearing 16 to 24 hours Immersion/Full Chemical Exposure 5 days Force cures may be used to enhance chemical resistance or to allow the coating to be placed in service before 5 days. Allow the coating a post cure to 12 to 24 hours before force curing. RECOMMENDED FORCE CURE SCHEDULE Minimum 2 hours @ 150oF Maximum 4 hours @ 200oF NOTE: this product will cure well at temperatures as low as 40-45 oF. However, additional curing time must be provided. CHEMICAL RESISTANCE PROPERTIES: ACIDS Hydrochloric 10% to 35% Sulfuric 10% to 98% Nitric 45% ALKALIES Ammonia 10% Sodium Hydroxide 10% to 50% SALTS Sodium Chloride Excellent Calcium Chloride Excellent SOLVENTS Alcohols, acetone, toluol, methyl cellulose, methanol.
Remove all grease, dirt and other contaminants from surface prior to sandblasting. Grind sharp edges to a radius of 1/8". Remove all weld splatters. Sandblast to a white metal finish according to SSPC-SP-5-63 or NACE standard TM-01-70 with a minimum anchor profile of 3 mils. APPLICATION: Product#711 can be applied by trowel or grout pump. Product #711 is designed as a one coat system (minimum 45 mils, maximum 80 mils). Relative humidity during the coating process should be 90% or less. Substrate temperature should be a minimum of 60°F for application to commence. If a second coat is needed before the first coat cures, no surface preparation is needed. Simply apply the second coat maintaining the required standards. However, if the first coat has cured (when it is tack free) the first coat must be brush blasted prior to the second coat.CAUTION: Society of the Plastics Industry (SPI) Classification and Warning for "A" Components: FOR INDUSTRIAL USE ONLY! WARNING! May cause skin sensitization or other allergic responses. Avoid inhalation of vapor. Use good ventilation, particularly if the material is heated or sprayed. prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. If contact with skin occurs, wash immediately with soap and water. In case of contact with eyes, flush with water and contact a physician. Manufacturing Chemists Association (MCA) Warning for "B" Components: CAUTION! DANGER! Causes severe burns. Contains alkaline amines; strong sensitizer. Do not get into eyes, on skin or clothing. Avoid breathing vapor. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling. FIRST AID! In cases of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Call a physician. Wear protective clothing, goggles, gloves and/or barrier creams. FOR INDUSTRIAL USE ONLY! KEEP AWAY FROM CHILDREN! |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
