Chemical Resistant Polyurethane Maintenance Coating
Excellent UV and Chemical Resistance
Epoxy.com Product #402
GENERAL DESCRIPTION
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating is a two component chemical
resistant polyurethane coating. The high gloss finish offers
excellent abrasion resistance, chemical and stain resistance, and
color retention.
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating can be used equally well on
vertical or horizontal surfaces. It is ideal for concrete floors and
walls in warehouses, storage facilities, aircraft hangers, animal
housing, and vehicle maintenance facilities.
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating is not for use in California
ADVANTAGES
- Excellent Abrasion Resistance
- Excellent Chemical Resistance
- UV Resistant - means a long life even in direct sunlight
- Excellent Color Stability - Pigmented Version
- Clear Version Resists Ambering Even in the Brightest Sunlight
- Exterior and Interior Uses
- May be used on both Horizontal and Vertical Applications
Epoxy.com Product #402
Clear
Over Chip Flooring - Over Basement Room
Picture Courtesy of Matt Dekman
Used with Permission - All Rights Reserved
SURFACE PREPARATION
Surface must be clean and sound. Remove all dirt, laitance, grease
curing compounds and other foreign matter by sandblasting, or
mechanical abrasion. Remove water and dust from all surfaces with an
oil-free blast immediately prior to application.
APPLICATION
Prime: For best bond to properly prepared surface,
use Epoxy.com
Product #899 Primer.
Body: Apply
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating
with brush, roller (short napped), or squeegee followed with back
rolling to get recommended thickness (3 mils DFT).
Finish: Apply top coat as required (minimum 3 mils
DFT).
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating is also available in the
following forms:
- As a slip or skid resistant finish using a non-skid additive in
the finish.
- As an electrostatic dissipating finish version -
Epoxy.com Product #675
LIMITATIONS
Epoxy.com Product #402
Clear
Over Chip Flooring - On Outside Patio
Picture Courtesy of AA Permacoat
Used with Permission - All Rights Reserved
Surface to receive
Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane
Coating must be dry. Minimum application temperature of 40°F
(Contact Epoxy.com Technical Support for Low Temperature Cure).
Maximum application temperature of 100°F. Avoid
applications on surfaces without effective vapor barriers.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and
skin irritation. If contact occurs, wash immediately and seek
medical help. Use safety glasses with side shields and wear
protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system gels.
Use MEK, Acetone, or any lacquer solvent.
Physical Properties
|
|
Color
|
Standard colors for this product are:
Clear (satin and gloss), White #001,
Light Gray #100, and Dark Gray. Other standard colors are
available with a 30 gallon minimum ordere
|
|
Gloss, 60°F
|
85-100
|
|
Mix Ratio
|
2Ato 1B by volume
|
|
Pot Life
|
30-40 minutes @ 70°F
|
|
VOC
|
405 gm/liter
|
|
Solids Content, % volume
|
56.0
|
|
Coverage
|
300 ft2/gal @ 3 mils DFT
|
DRY TIME
|
|
10-20 mil film
|
1O~14 hrs
|
|
Light Traffic
|
16 hrs
|
Ultimate Cure @ 74°F
@50°F
|
5 days
14davs
|
CHEMICAL RESISTANCE
|
REAGENT
|
Rating
|
REAGENT
|
Rating
|
|
Acetic Acid-5%
|
L
|
Iodine
|
R
|
|
Acetone
|
L
|
Lactic Acid-15%
|
R
|
|
Betadine
|
R
|
Methyl Ethyl Ketone
|
L
|
|
Bleach
|
L
|
Nitric Acid-10%
|
R
|
|
Citric Acid-30%
|
R
|
Skydrol
|
R
|
|
Crude Oil
|
R
|
Sodium Hydroxid-50%
|
R
|
|
Diesel Fuel
|
R
|
Sulfuric Acid-20%
|
R
|
|
Ethylene Glycol
|
R
|
Toluene
|
R
|
|
Fafty Acids
|
L
|
Urea
|
R
|
|
Gasoline
|
R
|
Vinegar
|
L
|
|
Hydrochloric Acid-15%
|
R
|
Xylene
|
R
|
R= Recommended for continuous Service
L=Limited recommendation, occasional spills
|
PERFORMANCE PROPERTIES
|
|
Adhesion to concrete ACI Committee 403
|
200 psi (concrete fails)
|
|
Abrasion Resistance ASTM-C501
|
30-40 mg loss
(CS-17 wheel, 1 kg load, 1000 cycles)
|
|
Service Temperature MIL- D-3134F
|
160°F (immersion) 250°F (dry heat)
|
|
Impact Resistance MTI-D-3134F ss 4.7.5
|
Withstands 16ft./lbs. no cracking, delamination or chipping
|
|
Elevated Temperature Resistance MIL-D-3134F ss 4.7.3
|
No slip or flow at required temperatures at 158°F
|
|
Water Absorption (24. hr. immersion) ASTM-D-670-63
|
0.10% maximum
|
|
Hardness ASTM D3363 |
2H± |
Standard colors
for this product are: Clear, White #001, and Light Gray #100.
BLOG POSTS & NEWS
You can find more information on
Polyurethane Products, and many of our other products at
news.epoxy.com.
Download this file in
Adobe Acrobat format for formal presentation.