|
|
|
Epoxy.com Product #20 100% Solids Low Viscosity Grout Resin
DESCRIPTION : Epoxy.com PRODUCT #20 is a moisture insensitive, two-component, 100% solids epoxy resin system manufactured specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of Product #76 -Epoxy Filler (by volume). PRODUCT #20 exceeds most requirements of ASTM C-881-90, Types I, Grade 1, Class A.
ADVANTAGES:
WHERE TO USE:
PHYSICAL PROPERTIES:
Slant shear tests meet and exceed requirements of ASTM C 882. Allow 10 to 15 minutes open time to apply PRODUCT #20, prior to placement of fresh concrete, when testing slant shear at 40°F (4°C). SURFACE PREPARATION: All surfaces to receive Epoxy.com PRODUCT #20 must be free of dirt, grease, curing compound, liquid contaminants, heavy laitance and soft or deteriorated concrete. It's recommended that abrasive blasting, water blasting or acid etching with a 10% solution of commercial muriatic acid be utilized for surface preparation. Vacuum all areas prior to application to remove fine particles of cement or sand. Surface must be sound.MIXING: Combine two parts by volume of "A" Component with one part by volume of "B" Component (mixing ratio is 2:1). For best results, mix entire unit. The blend should be thoroughly mixed for at least three minutes with a low speed 1/2" electric drill and Epoxy.com Mixing Paddle. If used as a mortar, introduce the Epoxy.com Product #76 -Epoxy Filler slowly while mixing to assure proper aggregate saturation.APPLICATION: Keep Epoxy.com PRODUCT #20 warm where possible. This will facilitate mixing and application. No ice should be present when applying.YIELD: One (1) gallon (3.8 L) of PRODUCT #20, with 3 to 3 1/4 parts of Product #76 -Epoxy Filler, provides approximately 645 cu. in. (1 x 10 cm ) of mortar.LIMITATIONS: Do not thin; solvents will prevent proper cure. Use only oven-dry aggregate to avoid encapsulation of moisture.CAUTION: "B" Component: CAUTION! DANGER! Contains aliphatic amines. May cause burns, skin sensitization, and other allergic responses. Do not get into eyes, on skin or clothing. Avoid breathing vapors. Keep containers closed. Use with adequate ventilation. In case of contact with eyes or skin, flush immediately with plenty of water for at least 15 minutes. Call a physician. Wear protective clothing, goggles, gloves and/or barrier creams. Remove contaminated clothing and wash before reuse. Discard contaminated shoes.
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
