Epoxy.com Product #900Gun Grade Polymeric Joint SealantDESCRIPTIONEpoxy.com PRODUCT #900 Polymeric Joint Sealant is a 2 part chemically cured elastomers. They provide a flexible and watertight seal between concrete, masonry, metals, glass, wood, and other construction materials. Product #900 (Gun Grade)/ Product #901 (Pourable) are mixed just prior to application. Color is light gray. (Other colors are available on special order.) Related and Similar ProductsADVANTAGES:Epoxy.com Product #900 Polymeric Joint Sealant bonds tightly to any clean, dry surface. The cured sealant have excellent flexibility and performs well to -20°F. Joint movement of plus or minus 25% is easily accommodated through years of outdoor exposure. Epoxy.com Product #900 Polymeric Joint Sealant resist the effects of temperature extremes, seasonal weather changes, sunlight, moisture and chemical attack. Life expectancy is up to 20 years under normal conditions. PHYSICAL PROPERTIES:Epoxy.com Product #900 Polymeric Joint Sealant has excellent electrical properties. Typical electrical properties of cured material at 77°F (25°C) and 50% relative humidity are as follows:
SPECIFICATION:Epoxy.com Product# #900 Polymeric Joint Sealants meets the following specifications:
National Bureau of Standards and GSA TT-S-0227E (1970) * * Defers test specification to ASTM C-920-95 SURFACE PREPARATION:Joint interface must be clean, dry, and free from oils, loose mortar, laitance, waterproofing, and other contaminants. A thorough grinding, sandblasting, or solvent cleaning may be required to expose clean, sound surfaces. Priming is not normally required with common building materials. However, an instance may occur where priming is necessary for certain substrates or for water immersion, and Epoxy.com Product #950 Sealant Primer should be used. The Product #900 must be applied within 8 hours after priming. Re-prime if time limit has expired. MIXING:Mix "A" and "B" Components with a slow speed mechanical mixer for 3 minutes. Use Product #900 with caulking gun or mechanical equipment. If you need a pourable product use Epoxy.com Product #901. APPLICATION:Apply immediately after mixing into properly sized joints. Backer Rod may be required. Can be applied with a trowel, putty knife, auto-body filler squeegee, concrete grout bag, bulk caulking gun, or similar devices. PRIMERIf a primer is required use Epoxy.com Product #950 Joint Sealant Primer. Product #950 Joint Sealant Primer is a one component moisture curing primer formulated to improve adhesion of our Epoxy.com Joint Sealants. Epoxy.com Product #950 Joint Sealant Primer is easy to use and provides extra protection in applications where standing water or submersion will be present. Epoxy.com Product #950 Joint Sealant Primer acts to increase bond between organic and inorganic interfaces, binding together weak areas and creating a tough surface.
LIMITATIONS:Do not install in damp or wet joints. Temperature should be above 40°F (4.4°C) at time of application to assure proper curing. CAUTION:Repeated or prolonged contact with skin should be avoided; protective gloves should be worn as a precaution. Avoid contact with eyes; in case of eye contact, flush with water for 15 minutes and consult a physician. Other customers who visited this page also visited:
FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
