Epoxy.com Product #406

Two Component Low VOC Chemical Resistant Polyurethane Coating

Skip Navigation Links

DESCRIPTION

Epoxy.com Product #406 is a two component, chemical resistant, polyurethane coating. Epoxy.com Product #406 is a low VOC compliant urethane that meets all federal and state environmental air quality standards. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance, and superior color retention.Epoxy.com Product #406 can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangars, animal housing, and vehicle maintenance facilities. Available in both clear and pigmented formulations, Product#406 can be used as a finish coating option for most Epoxy.com Flooring Systems.

ADVANTAGES

CONSIDERATIONS

COMPOSITION

Two component, catalyzed, chemical resistant polyurethane.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. Work must be performed by trained or experienced contractors or maintenance personnel.

INSTALLATION

Epoxy.com Product #406 is normally applied with a brush, short napped roller, or squeegee and back-rolled with a short nap roller. Care should be taken to minimize the entrapment of air caused by over-rolling.

Epoxy.com Product #406 can also be applied by airless or conventional spray. May be thinned 9-10% with Ethyl Ethoxy Propanate (EEP) or Methy Amyl Ketone (MAK).

CLEAN UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

COVERAGE

Epoxy.com Product #406 Clear will yield approximately 2.9 mils dry film thickness when spread at 300 ft2 per gallon.

Epoxy.com Product #406 Pigmented will yield approximately 3.5 mils dry film thickness when spread at 300 ft2 per gallon.

COLOR SELECTION

Epoxy.com Product #406  is available in Clear (gloss or satin) and 17 colors. Custom Colors are available subject to laboratory approval, minimum quantity, lead time for production, and increased cost.

TECHNICAL DATA

Viscosity @ 75ºF 125-150 cps, mixed, Clear
Mixing Ratio 3 Parts A to 1 Part B by Volume
Solids Content (by Volume) 54.26% Clear
66.46% Pigmented
Volatile Organic Content (VOC) 1.56#/gal (187 gm/L) Clear
1.39#/gal (166 gm/L) Pigmented
Weight per Gallon 9.85 pounds per gallon , mixed, clear

CURE/DRY TIME

Pot Life 8 hours @ 75ºF
Dry to Touch 10-14 hours @ 75º
Re-Coat 12-16 hours @ 75º
Light Service 16 hours @  75º
Full Cure & Maximum Resistance 5-10 days

AVAILABILITY

Contact Epoxy.com

MAINTENANCE

After completing the application of Epoxy.com Product #406, the installer should provide the owner with maintenance instructions.

Epoxy.com Product #406 is easily cleaned with neutral soaps or detergents.

TECHNICAL SERVICE

Epoxy.com Technical Support provide services and consultations on material selection, specification, troubleshooting, and other information on the proper repair and protection of concrete surfaces.

CHEMICAL RESISTANCE

REAGENT RATING

R-Recommended for continuous service.

L-Limited Recommendation, occasional spills.

*-May cause slight stain or discoloration.

Skip Navigation Links
Epoxy.com Home Page
Product CatologExpand Product Catolog
Important Links

Skip Navigation Links

Untitled Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 375 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
 
www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253



Copyright © 1994-2008 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Hit Counter

 

Secure Login