Epoxy Bonding Agent
Bonding Fresh Concrete to Hardened Concrete
Epoxy.com Product #2007
DESCRIPTION
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is a
two component, 100% solids epoxy resin system designed to bond new concrete to
old and other materials to concrete. It has a convenient 2:1 mix ratio, by
ASTM C-881-90, Types I, II, IV and V, Grade 2, Class "B" and "C"
volume with a viscosity similar to heavyweight oil. Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 (adhesive) exceeds the requirements of ASTM
C-881 Type II, Grade 2, Class "B" "C" "D" and E.
ADVANTAGES
- Meets ASTM C-881 Type II, Grade 2, Class "B" "C"
"D" and E.
- Is a Moisture Insensitive Epoxy Adhesive
- Multi-Function Epoxy - makes it suitable for many types of uses
- Very Little Odor
- 100% Solids
- Zero (0) VOC Epoxy Adhesive - No VOC means it meets the
strictest low VOC standards
USES
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
(adhesive) can be used for:
- New Concrete to Old Concrete Epoxy Binding Resin
- Epoxy Grouting Machine Base Plates
- Anchor Bolts Setting Epoxy
- An Epoxy Floor Topping with Good Chemical Resistant Properties
- A Skid-Resistant Epoxy Surface on Concrete, Steel or Timber
- A Protective Epoxy Coating.
APPLICATION
Bonding Agent
When Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is used as an adhesive, bonding new concrete to
existing surfaces, coat the existing area (concrete, steel, aluminum, wood) at a
rate of 100 square feet per gallon (9 m2) on smooth surfaces, 60 square feet on
rough (6 m2). Apply topping while Epoxy.com Product #2007 All Purpose Epoxy
Bonding Agent
(adhesive) is tacky; if dry, recoat.
Coating
When Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
is used as a protective coating, apply the material at a rate of 200 square
feet per gallon per coat (8 mils) (19 m2/3.79 L -or- 5 m2/L).
MIXING
Stir Component "B" thoroughly before combining with Component "A". Combine 2
parts volume of Component "A" with 1 part by volume of Component "B" for not less
than (3) three minutes, using a slow-speed drill motor (300 to 600 rpm) and
Epoxy.com Mixing Paddle for a uniform gray mixture. Scrape sides and bottom.
Avoid entrapping air in mixture. Apply immediately after mixing to properly
prepared surface.
APPLICATION
Surface must be clean and sound. Remove rust, grease and curing compounds by
best means available. Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
may be applied to dry or damp surfaces, but not in standing water. Apply by
brush, roller or spray. Place fresh concrete while Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
(adhesive) is still tacky. If epoxy hardens simply apply another coat.
PHYSICAL PROPERTIES
| Mix Ratio |
2:1 by Volume |
| Mix Viscosity |
3,500-4,500 cps |
| Bond Strength PSI Min. |
1,500 |
| Gel Time (150 g mass @ 70° F) |
30-40 min. |
| Flash Point in °F |
>200 |
| Consistency |
3,500 to 4,500 cps |
| Initial Cure |
24 hr. (80% ultimate strength) |
| Final Cure |
7 Days |
| Lineal Coefficient of Shrinkage |
.005 (max) |
| Compressive Modulus (psi) |
150,000 (min) |
| Compressive Yield (psi) at 7 day cure |
5,000 (min) |
| Tensile Strength @ 75 degrees F at 7 days |
4000 P.S.I (34.5 MPa) |
| Flexural Strength (psi) |
11,000 (min) |
| Heat Deflection Temperature °F |
120 (min) |
| Elongation at break (%) |
2.5 (min) |
| Thin Set Film set time hours |
7-9 |
| Peak Exotherm °F |
214 |
| v.o.c (mixed) |
0.0 |
| Coverage @ 30 mils |
53 sq. ft./gal |
| Packaging |
1.5 gal units, 3 gal units, 15 gal units |
| Shelf Life |
2 years |
LIMITATIONS
Application of Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
to surfaces with a temperature below 50°F (10.0°C) prolongs cure. Do not use if
surface temperature is below 50°F (10.0°C).
CHEMICAL RESISTANCE
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is excellent against distilled water, most inorganic
acids and alkalies and moderate against alcohols or aromatic solvents.
BLOG POSTS & NEWS
You can find more information on
Epoxy Gel Adhesive Products, and many of our other products at
news.epoxy.com.
NOTICE TO BUYER
DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
Products are manufactured to strict quality assurance specifications and that
the information supplied by us is accurate to the best of our knowledge. Such
information supplied about our products is not a representation or a warranty.
It is supplied on the condition that you shall make your own tests to determine
the suitability of our product for your particular purpose. Any use or
application other than recommenced herein is the sole responsibility of the
user. Listed physical properties are typical and should not be construed as
specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER
INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM
ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE
MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO
WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT
INFRINGE UPON ANY PATENT. We shall have no liability for incidental or
consequential damages, direct or indirect. Our liability is limited to the net
selling price of our product or the replacement of our product, at our option.
Acceptance of delivery of our product means that you have accepted the terms of
this warranty whether or not purchase orders or other documents state terms that
vary from this warranty. No representative is authorized to make any
representation or warranty or assume any other liability on our behalf with any
sale of our products. Our products contain chemicals that may CAUSE SERIOUS
PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW
ALL PRECAUTIONS TO PREVENT BODILY HARM.