Epoxy Tabletop Resin - Epoxy Bar Top Resin
Water Clear Epoxy Casting Resin
Product #214
Table Top Resin Description
Product #214 Water Clear Epoxy Casting - Tabletop Resin - Bar Top Resin is an all-purpose, low viscosity
epoxy resin system for coating
wood
and concrete counter tops, tabletops, bar tops and similar applications.
Product #214 Water Clear Casting-Tabletop-Epoxy Bar Top
Resin is commonly used as a clear self-leveling flooring material, where an
extremely flat and level floor is required over concrete and wood.
Product #214 Casting-Epoxy Tabletop-Epoxy Bar Top Resin is used extensively for ultra flat leveling of surfaces
under equipment, where a very strong ultra flat bearing surface is a must.
It is also used successfully for ultra flat floors for stages, dance floor, and
clean rooms.
Product #214 Clear Casting-Tabletop-Bar Top
Resin is used as a clear adhesive matrix for specialty colored glass and colored
aggregate flooring and tiles. Product #214 Clear Casting-Clear Tabletop Resin -
Clear Bar Top Resin forms a glossy, hard surface, which
is resistant to stains. It is also used extensively as a water clear
casting resin.
Product #214 Clear Casting- Clear Tabletop- Clear Bar Top
Resin has excellent clarity and color retention. Product #214 Clear
Casting Resin-Tabletop Resin-Bar Top Resin has zero (0) VOC making it essentially
odorless and can therefore be used in occupied areas.
Advantages of Clear Table Top Resin #214
- Low odor for use in occupied areas
- Low viscosity - good wetting properties
- Meets USDA standards for use in food handling applications
- Glossy finish
- Stain resistant
- Zero (0) VOC - No VOC means it meets the toughest low VOC
standards.
Consideration When Using Clear Table Top Resin
- Minimum application temperature of Product #214 Clear Epoxy
Casting-Tabletop-Bar Top Resin is 50° F.
- Substrate to receive Product #214 Water Clear Resin must be free of curing agents and any foreign materials.
Surface Preparation of Table Top Epoxy
Surface Preparation is the most critical portion to any successful epoxy
application. All substrates to receive Product #214 Water Clear Casting-Tabletop-Bar Top Resin must be properly cleaned and prepared. Substrate
must be free of oil, paint, sealer, caulking, and all other contamination that
will interfere with the bonding of this material. Please see
Surface Preparation. Contact us
for more details.
Mixing Instructions for Clear Resin #214
Stir each component separately. Combine 2 parts A to one part B by volume
into a clean container. Stir for three minutes, with an Mixing Paddle, scrapping bottom and sides of
container frequently. Do not add thinners.
APPLICATION PROPERTIES @77°F |
| Mix Ratio | 2:1 By Volume |
| Viscosity (mixed) | 950 CPS |
| Pot Life (200 gr.) | 30-40 minutes @ 70° F. |
| VOC |
0 |
| Cure Time
(recoat) |
10-14 Hours |
| Ultimate cure
@ 74 Degrees F. |
5 days |
| Color |
Clear |
|
Packaging Unit Size |
3 gallon
units |
Performance Properties |
| Tensile Strength ASTM D-638 |
8500 psi |
| Elongation ASTM D-638 |
5.5% |
| Adhesion to metal |
2500 psi |
| Adhesion to concrete ACI
Committee 403 |
350 psi
(Concrete fails) |
| Hardness ASTM D-2240 |
80 (Shore D) |
| Abrasion Resistance ASTM
C-501 |
35-40 mg loss
(CS-17 wheel, 1kg load, 1000 Cycles) |
| Service Temperature
MIL-D-3134F |
160 F
(Immersion)
185 F (Dry Heat) |
| Impact Resistance MTI-D-3134F§ 4.7.3 |
Withstands
16ft/lbs no cracking,
delamination or Chipping. |
| Indention MIL-D-3134F §4.7.4 |
Withstands 2000
lbs./sq. in. for 30
minutes without indentation |
Elevated Temperature
Resistance
MIL-D-3134F § 4.7.5 |
No slip or flow
at required temperatures at
158 F. |
Water Absorption ASTM
D-570-63
(24 hour immersion) |
0.10% maximum |
| Flexural Strength ASTM D-790 |
8000 psi |
| Compressive Strength ASTM
D-695 |
11000 psi |
Application of Table Top / Bar Top Epoxy
Application of Product #214 Water Clear Resin will vary with application method. Be careful not to incorporate bubbles into
the coating. Typical pours are in the 1/16 inch to 1/2 inch thick range per
coat. If a second coat is desired, remove
all dust, if more than 24 hours after the last coat lightly sand, and then apply second coat.
Safety Precautions When Using Epoxy
Keep away from children. Refer to the Material Safety
Data Sheets (MSDS forms) pertaining to this product before using. Avoid contact
with skin or eyes. Prolonged or repeated exposure may cause eye and skin
irritation. If skin contact occurs, wash immediately with soap and water. If
contact with eyes occurs, flush eyes as required with clean water and seek
medical help. Use safety glasses with side shields and wear protective rubber
gloves.
Cleaning up Epoxy Tabletop - Bar Top Resin
Remove Product #214 Water Clear Resin from all tools and equipment before the system gels. Use MEK,
Acetone, or any lacquer solvent.
Chemical Resistance of #214 Bar Top Resin
| Acetic Acid 5% |
L |
Lactic Acid- 15% |
R |
| Acetone |
L |
Methyl Ethyl Ketone |
L |
| Methyl Ethyl Ketone |
L |
Nitric Acid 10% |
R |
| Bleach |
L |
Sodium Hydroxide 50% |
R |
| Citric Acid 30% |
R |
Skydrol |
R |
| Crude Oil &
Diesel Fuel |
R |
Sulfuric Acid 20% |
R |
| Ethylene Glycol |
R |
Toluene |
R |
| Fatty Acids |
L |
Urea |
R |
| Gasoline |
R |
Vinegar |
L |
| Hydrochloric Acid 15% |
R |
Xylene |
R |
R=Recommended for continuous service L=Limited recommendation, occasional
spills.
Coverage: 231 cubic inches per gallon. At
1/8 inch thick 12.8 SF Per gallon.
Use the Top Resin Calculator to double check your
estimate.
More Information
Information on using Table Top Resin in a
River Simulation.
|