DESCRIPTION:
Epoxy.com Product #954 Joint Sealant is a two component extended
polyurethane elastomer self-leveling joint sealant for joints in concrete,
asphalt, or metal. When poured into a horizontal joint, Epoxy.com Product
#954 is an excellent elastomeric joint sealer with "great memory".
Epoxy.com Product #954 is also available for machine mixing.
Epoxy.com Product #954 may be used as a relief joint by mixing it with
one part by volume of Epoxy.com Product #75 Filler.
ADVANTAGES:
- Easy to use: Epoxy.com Product #954 is manufactured in a
convenient 1:1 mix ratio by volume.
- Pourable & Self Leveling: With extremely good flow. No special
equipment is required for most applications.
- Rapid Cure: Tack free in less than 4 hours at 75°F. Prevents delay
in opening joints to traffic.
- Excellent Bond: Holds bond even after immersion in water or jet
fuel. No loss in adhesion in below freezing temperatures.
- Good Tear Resistance: Cured material is tough and resists
puncture and tearing by sharp objects.
- Flame & Fuel Resistant: Does not ignite, flow, or drip when
subjected to flame test. Does not swell or soften when exposed to jet
fuel.
SPECIFICATIONS:
ASTM C-920, Type M, Grade P, Class 25, Use T, NT and M.
Federal Specification SS-S195B (St. of Maryland)
Federal Specification SS-S200D (Jet Fuel Resistant)
JOINT PREPARATION:
Clean all surfaces of oil, grease, curing compound, residue, rust, or
other foreign materials by sandblasting or mechanical blasting. Remove loose
particles by oil-free compressed air or vacuum. Joint slot surfaces must be
dry at time of application. Apply masking tape along edges of joint slot for
neat, straight edges. Remove tape immediately after sealant levels.
MIXING:
Mix components A & B separately for 2 to 3 minutes, then mix one part of
A to one part of B by volume. Mix at medium speed with mixing paddle, moving
paddle from top to bottom and around sides of container to insure thorough
and complete mixing. Suggested mixing time for 2 gallon units is 4 minutes;
5 minutes for 10 gallon units.
APPLICATION:
Pour mixed Epoxy.com Product #954 into joint slot from the
container or from a metal or plastic watering can after removing the
sprinkler head. For large jobs, automatic metering, mixing and/or placing
equipment may be used.
COVERAGE:
One gallon of Epoxy.com Product #954 fills 231 cu. in. of joint or
75 LF of 1/2" x 1/2" joint. Primer is required on steel. Primer is not
required on concrete and other porous materials.
PACKAGING:
Epoxy.com Product #954 is packaged in 2 gallon, 10 gallon and 110
gallon units.
LIMITATIONS:
Joint slots must be dry. Shelf life is 6 months for Epoxy.com Product
#954. Do not dilute Epoxy.com Product #954.
CAUTION:
Epoxy.com Product #954 contains coal, tar, and organic
isocyanates. These are considered irritants. Provide adequate ventilation.
Contact with skin or eyes must be avoided. Wear protective clothing,
goggles, gloves, and/or barrier creams. Wash thoroughly with soap and water
or a waterless skin cleaner prior to smoking or eating. In case of contact
with eyes, flush immediately with water and contact a physician. If
swallowed, call a physician immediately.
PROPERTIES:
| Color |
Mixed - Black |
| Viscosity |
6,000-10,000 cps |
| Approx. effect of temperature |
60°F |
70°F |
90°F |
| Pot Life |
25 min |
20 min |
15 min |
| Tack-Free Time |
4 hrs |
3 hrs |
2 hrs |
| Shore A Hardness @ 72 hrs max |
25 +/- 5 |
25 +/- 5 |
25 +/- 5 |
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
Untitled Page
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
375 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2007 EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy
Systems™ Product Company ("ESI") warrants its products (when properly stored)
for the period of time as follows: Epoxies, Product #315, Product #315BC, and
Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2)
months and Polyurethanes Four (4) months; Power Tools and Equipment 90
days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all
other resins (not specifically mentioned above) 30 days; hand tools (non-power
tools) 30 days. ESI warrants that its products will be free of
manufacturing defects and will be in conformity with published specifications
when handled, stored, mixed and applied in accordance with recommendations of
ESI. If any product fails to meet this warranty, the liability of ESI will be
limited to replacement of any non-conforming material if notice of such
non-conformity is given to ESI within the warranty period for the material (as
indicated above), or within 1 year of the delivery of materials (whichever is
sooner). ESI may in its discretion refund the price received by ESI in lieu of
replacing the material. No customer, distributor, or representative of ESI is
authorized to change or modify the published specifications of this warranty in
any way. No one is authorized to make oral warranties on behalf of ESI. In order
to obtain replacement or refund the customer must provide written notice
containing full details of the non-conformity. ESI reserves the right to inspect
the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED
WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY
UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY,
WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of
our products are made on an individual order basis. Unless
authorized in writing by Epoxy Systems, Inc. in writing before the material is
made, there are no returns on items purchased from us, once the order has been
processed, and the material made. In the event of authorized returns a
restocking charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on non-list
priced items. All Returns are for merchandise (store) credit only, no cash
or credit card credits. In the event of a return, buyer is responsible for
the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
Secure Login