Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Electro Static Dissipative Epoxy Floor Coating

Ultra High Solids ESD/Conductive Epoxy Floor

Epoxy.com Product #1ESD


Description

Electrostatic Dissipative Epoxy Coating for ESD Epoxy Flooring  - Product #1-ESD is an ultra high solids bis-A epoxy floor coating designed to provide electrostatic control properties to various surfaces including concrete or other nonconductive substrates. The use of a conductive primer will transmit conductive readings through ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring Epoxy.com Product #1 if applied no thicker than 15 mils.

ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring Epoxy.com Product #1-ESD  provides excellent bond to concrete as well as high impact and wear.

Advantage

  • Easy Application
  • Dissipates a 5000 volt Charge to Zero in less than 0.1 Seconds @72°F and 12%RH.
  • Available in Static Dissipative Range of 1,000,000 to 1,000,000,000 ohms per EOS/ESD Standards.
  • Can be made Conductive (100,000 to 1,000,000 OHMS by priming with Product #668
  • Consistent Electrical Resistance Ratings When Tested at 10-500 Volts.
  • High Gloss
  • Good Abrasion Resistance.
  • Easy to Clean..

Considerations

  • Test for moisture vapor transmission using anhydrous calcium chloride test as per ASTM F-1869 and/or situ RH probe testing per ASTM F-2107. Maximum MVT is 3 pounds per 1000 SF per 24 hour period. Above these values use Product #100MR Moisture Tolerant Epoxy Primer and Basecoat or Product #830 Moisture Vapor Epoxy treatment.
  • Substrates Temperatures must be a minimum of 55-60°F. and a maximum of 85°F.
  • Relative Humidity (RH) should be between 30% and 85%. Substrate must be 5°F above the measured dew point.
  • Substrate must be clean and free of Dirt, waxes, curing agents and any other foreign material that will interfere with bonding. See Epoxy.com Surface Preparation Guide for more details.

Composition

Ultra High Solids Bis-A Epoxy Resin and Conductive Fillers.

Epoxy.com Epoxy Color Chart Here

Color Selection

ESD (Electrostatic Dissipative) Epoxy Floor Coating for ESD Flooring Product #1-ESD  is available in Epoxy.com Colors listed to the right. Custom colors available as approved.

Application

Surface Preparation

Surface preparation is considered to be the most important step of any resinous flooring application. Improper surface preparation could turn what seems to be a simple process into a lengthy, difficult repair. See Epoxy.com Surface Preparation Guide for proper surface preparation procedures.  When in doubt you should always contact Epoxy.com Technical Support with your questions.

Installation

Electrostatic Dissipative (ESD) Epoxy Floor Coating -  Product #1-ESD is normally spread with a trowel or squeegee and back-rolled with a 3/8" medium nap roller. Care should be taken to minimize the entrapment of air caused by over rolling.

Clean Up

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

Coverage

ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring  - Product #1ESD will yield 12-15 mils when spread at 100-130 sq ft/gal. 15 mils is considered the maximum thickness.

Maintenance

After completing the application of ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring  - Product #1ESD, the installer should provide the owner with maintenance instructions relevant to the specific topcoats or floor covering. If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.

Availability

Contact Epoxy.com Customer Service Department.

Physical Data

Flammability ASTM D-635        Self Extinguishing
Fungus & Bacteria Growth Mil-F 52505§4.4.2.11     Will not support growth of fungus or bacteria
   when subjected to mildew
Hardness  ASTM D-2240 70-80 Shore D
Bond Strength to Concrete      ASTM D-4541 Greater than 300psi (100% concrete failure)
Water Absorption ASTM D-570 Nil 
Thermal Shock Resistance ASTM C-884 Passes
Abrasion Resistance ASTM D-6040 75-100mgs
Impact Resistance ASTM D-2794  100 in-lbs direct 

Technical Data

Pot Life 35-40 Min. (@73°F)
Foot Traffic  14-16 hours (@73°F )
Complete Cure  5 days (@73°F.)
VOC Content  Less than 50gm/l
Weight per Gallon  10.5-11 lbs per gal. 
Glass, 60° Greater than 80

Technical Service

Consult the Installation Manual for ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring  - Product #1ESD or Contact Epoxy.com Technical Support Department.

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.