|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|
EpoxySystems' Product #458 Two Component Polyurethane Coating This Material requires a minimum product purchase. Please Use Epoxy.com Product #402 instead. EPOXYSYSTEMS’ PRODUCT #458 is a liquid-applied, two-component, catalytic cured polyurethane floor and wall coating for use in air fields, industrial plants, stores, and other locations where surfaces must withstand heavy use of foot traffic. DESCRIPTION Composition: EPOXYSYSTEMS’ PRODUCT #458 is a catalytic cured liquid polyurethane, based on Aliphatic Isocyanates in combination with additives and pigments to produce a wear resistant, protective floor coating, for interior and exterior applications. EPOXYSYSTEMS’ PRODUCT #458 is ideally suited for coating walls that are commonly subjected to graffiti. The cured product is easily cleaned with trichloroethylene or perchloroethylene and detergent. Basic Uses: EPOXYSYSTEMS’ PRODUCT #458 provides a durable finish that protects floors against occasional chemical spillage, dirt, grease and oil. PRODUCT #458 gives industrial floors a well maintained look while retaining a glossy appearance. Dusting of concrete floors is eliminated when the surface is sealed with EPOXYSYSTEMS’ PRODUCT #458 and, as dirt and oils are prevented from penetrating the concrete, detergent and water easily clean the floor. EPOXYSYSTEMS’ PRODUCT #458 in pigmented form may be used on floors to hide an unsightly appearance of the substrate or to provide a reflective, bright appearance that will lighten up a warehouse, highlighting work areas and traffic lanes. Limitations: All surfaces to be coated must be completely free of foreign matter and completely dry. Color: Grey, tan, and clear. Sizes: Available in 1-1/2 and 4-1/2 gallon kits. Weight 8.6 lbs./gallon.
TECHNICAL DATA
INSTALLATION Surface Preparation: EPOXYSYSTEMS’ PRODUCT #458 may only be applied to dry, clean, surfaces. It is recommended that concrete floors be prepared by abrasive cleaning such as dust-free grinding, shot-blasting, or sandblasting. All oxidation must be removed from metal surfaces and all metal surfaces must be primed with EpoxySystems’ Product #887 Metal Primer. Application: EPOXYSYSTEMS’ PRODUCT #458 may be applied by all conventional means including spray equipment, roller and brushes. The recommended application rate of EPOXYSYSTEMS’ PRODUCT #458 is two coats minimum, 200 sq. ft. per coat. A thin coat of EPOXYSYSTEMS’ PRODUCT #458, at the rate of 200 to 250 sq. ft. per gallon, may be used as a primer coat if one is needed. If a metal substrate however, you must use EpoxySystems’ Product #877 Metal Primer. The second and third coat may be applied after an over-night cure, but it is important for proper bonding, not to wait for more than 24 hrs. before recoating. If necessary, a fine aggregate may be incorporated into the system to provide a non-slip surface. Allow 48 hr. final cure time before coating is exposed to traffic.
PRODUCT WARRANTY All products proven to be defective in manufacturing will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damages in excess of the purchase price of these products.
MAINTENANCE If PRODUCT #458 is damaged, it can be repaired by cleaning the surface with M.E.K. and recoating it with PRODUCT #458system.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
