|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|
EpoxySystems' Product #913 Two Part Polysulfide Sealant This Material requires a minimum product purchase. For smaller Quantities use Epoxy.com Product 900 (gun grade) or 901 (pourable) or Product #964 or Product #965. PRODUCT #913 is a two-part, self leveling or gun-grade, polysulfide sealant , which effectively seals joints that are subject to structural or thermal movement, as well as non-moving joints, against infiltration of water and dirt. DESCRIPTIONComposition: Polysulfide based joint sealant.Basic Uses: For use in sealing reservoirs, dams, canals culverts, and flood control channels. Also used for sealing curtain-wall panels, tilt-up panels, window glazing, flashing and metal setting. Also, for all joint-seal applications, such as expansion and contraction joints in shopping centers, sidewalks or other traffic areas. It will effectively prevent water from entering the sealed joints and thereby eliminate erosion of the soil underneath the slabs, particularly areas which are exposed to water frequently, such as swimming pool decks and around planters. All coping joints and deck joints should be sealed. In adobe soil areas, unsealed joints may cause swelling of the soil and subsequent buckling and cracking of the concrete slab. PRODUCT #913 maintains a low modulus of extension even after prolonged exposure to the elements. This prevents adhesive and cohesive failures which often occur when a caulking compound hardens excessively with aging. Limitations: The PRODUCT #913 is preferred for joints that are subjected to traffic, or severe movement shortly after sealant installation, and for joints of such large dimension that Product #905 would require too much time to cure throughout. Primers may be necessary for certain applications. Colors:
Sizes: Available in 1 1/2 and 4 1/2 gallon kits. Weighs 12 lbs. per gallon (5.4 kg/gallon). Standards: Federal Specification TT-S-227e and also USASI Specification A116.1-1967 Class A and B, A.S.T.M. C-920 type M, grade P, NS, class 25. s
INSTALLATIONJoint Design: Suitable for all properly designed joints following accepted engineering practices. Joint width must be a minimum of 4 times the anticipated movement.Surface Preparation: All joints must be absolutely clean. For concrete, sandblasting is recommended. All curing compounds, old caulks, grease, waterproofing compounds, etc., must be removed. For non-porous surfaces such as glass, metal, etc., cleaning with M.E.K. or Toluene is recommended. Polyethylene rod or polyurethane foam is recommended as a joint-filler and back-up material. Fillers treated with bituminous products, grease or oil, should not be used. Where present, they must be removed or separated by vinyl tape or polyethylene film. Consult Manufacturer for primer recommendations on certain surfaces or special applications. Application: Apply by caulking gun, hand or pressure type, or pour from container. Bulk sealant can be applied by pumping equipment, trowel or putty knife. Press firmly into joint to assure good contact. All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot assume any risk or liability for results obtained, nor can we accept damages in excess of the purchase price of these products. Other Products That May Interest YouIf you do not need the high flexibility of Product #913 and need a higher strength material please see EpoxySystems' Product #900& Product #901.The results are based on seven day submersion* NE= No Effect
Hydrofluoric Acid 5% NE MAINTENANCEIf PRODUCT #913 is damaged, and the joint has not been contaminated, it can be repaired by cutting out that part and resealing it with PRODUCT #913
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
