WATERPROOFING SYSTEM

This Product is Replace By Epoxy.com Product #449

This Material requires a minimum product purchase. Please see our Products That Require a Minimum Order Page, or contact Epoxy.com for more information.

EPOXY SYSTEMS’ PRODUCT #418, a black, self-leveling, liquid applied, two-component polyurethane system, designed to form a tough rubber membrane impervious to moisture.

Type I: For horizontal surfaces

Type II: For vertical surfaces

PRODUCT DESCRIPTION

Composition: Polyurethane elastomer. A two-component system, which does not depend on atmosphere moisture to cure.

Basic Uses: Once cured, EPOXY SYSTEMS’ PRODUCT #418 allows expansion and contraction over a broad temperature range and maintains flexibility and waterproofing properties under continuous exposure to water above or below grade. EPOXY SYSTEMS’ PRODUCT #418 has a thixotropic consistency and may be used on vertical as well as horizontal surfaces. EPOXY SYSTEMS’ PRODUCT #418 remains flexible from -75o to 175oF.

Suggested areas of application are as follows:

· Waterproofing in between slabs, such as parking decks, roof decks or courtyard areas over subterranean parking.

· Waterproofing exterior walls or foundations and basements or other structures that are to be backfilled.

· Waterproofing inside planter boxes.

· Waterproofing under terrazzo or tile floors.

· Waterproofing under shower pans, kitchen, laundry and bathroom floors.

· Waterproofing of occupied areas under malls, plazas and promenades.

Advantages:

· Applied cold by spray methods, brush, roller, squeegee or trowel.

· May be applied over concrete, stone, brick, cement blocks, wood, metal, asbestos and most other surfaces.

· EPOXY SYSTEMS’ PRODUCT #418 cuts cost of application by eliminating mixing, splicing, sealing tapes, adhesives and other labor consuming methods required when installing other conventional types of waterproofing systems.

· The superior flexibility and elongation properties of EPOXY SYSTEMS’ PRODUCT #418 allows expansion and contraction with the substrate, without cracking or becoming brittle.

· Excellent adhesion, combined with the elastomeric qualities of EPOXY SYSTEMS’ PRODUCT #418 makes the use of protective covering prior to backfilling unnecessary, unless the backfill material contains crushed rock. On in between slab applications, a protective board must be used.

· Does not contain any potentially hazardous coal tar.

Color: Black only.

Standards: A.S.T.M. C836-76

 

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

Copyright © 1994-2008 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Secure Login