|
Epoxy.com Product # 229 Two Component, Water Based, High Performance Coating Raw Materials for this material are currently on National Back Order - Please contact Epoxy.com Technical Support at 321-206-1833 for an alternate product. DESCRIPTION Epoxy.com #229 is a two component, water based, high performance coating suitable for concrete and other commonly used building materials. Epoxy.com #229 combines the exterior durability and gloss retention of acrylic with the adhesion and toughness of epoxy. Features of Epoxy.com #229 include excellent resistance to abrasion, staining, and common chemicals. Epoxy.com #229 has excellent interior and exterior durability. Epoxy.com #229 was developed as a high performance topcoat for protection of exterior/interior concrete floors and walls. It is ideal for clean rooms, laboratories, driveways, garages, walks, and patios.ADVANTAGES • Low Odor During Application & Cure• Fast Dry & Re-coat Time• Easy Clean-Up• Low VOC• Stain Resistant• Good Gloss & Color RetentionCONSIDERATIONS • Not recommended for use where strong solvents are anticipated.• Substrate temperature must be a minimum of 50ºF and relative humidity below 85% for proper cure.• Substrate must be free of dirt, waxes, curing agents, and other foreign material.• Typically self-priming, but depends on density and condition of substrate. Product may require two coats.COMPOSITION Waterborne Acrylic Epoxy. COLOR SELECTION Epoxy.com #229 is available in most Standard Colors. Contact Epoxy.com for assistance.APPLICATION SURFACE PREPARATION Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined on the Epoxy.com website. Epoxy.com Technical service department is pleased to answer any questions.INSTALLATION Mix each component of Epoxy.com #229 prior to combining. Mix 1 part Part A with 4 parts Part B and allow to stand 15-30 minutes before applying. Roll mixed Epoxy.com #229 at a rate of 300-400 ft2 per gallon with a non-shedding, short nap roller. Care should be taken to avoid puddles. Do not build a film of the sealer. Roll out so that it soaks into the concrete. Two coats are necessary to insure uniform wetting and coverage when used as a stand alone sealer. The second coat may be applied as soon as the first coat is tack free. For complete installation instructions, contact Epoxy.com technical service department . CLEAN UP Skin and tools can be cleaned with soap and water. Xylene and/or lacquer thinner will also clean tools and equipment. Consult Material Safety Data for safety and health precautions. RE-COAT/CURE TIMES Epoxy.com #229 can be re-coated very rapidly. Follow the re-coat windows specified below:• Re-coat 3-6 hours• Light Traffic Overnight• Heavy Traffic 5-7 days• Thicker application and cooler temperatures will lengthen tack free time.COVERAGE Epoxy.com #229, when applied at 300 ft2, yields 1.8-2.0 mils dry film/TECHNICAL DATA
CURE/DRY TIME
Higher temperatures and good ventilation will accelerate dry times; lower temperatures and higher humidity will lengthen dry times. MAINTENANCE Epoxy.com #229 is easily cleaned with neutral soaps or detergents. Routine mechanical scrubbing is recommended for all surfaces having a non-skid texture. Long periods of heavy traffic may cause wear patterns necessitating a maintenance application of a finish coat. |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
